User manual ZYXEL ZYWALL IDP 10

[. . . ] 14 Figure 11 Wizard­ Password Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 12 Wizard­ Network Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2 ZyWALL IDP 10 Quick Start Guide Figure 13 Wizard­Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 14 Wizard­ Stealth Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Your computer should have a terminal emulation communications program (such as HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow control and 9600 bps port speed. 4. 2 Rear Panel Figure 4 Rear Panel Power Connection Table 2 Rear Panel Power Connection LABEL POWER 5V, 4A DESCRIPTION Connect the included power adaptor to this power socket. 8 ZyWALL IDP 10 Quick Start Guide Table 2 Rear Panel Power Connection LABEL DESCRIPTION WARNING: Using an incorrect power adapter will damage your device! After you've made the connections, use the power cord to connect the power adaptor to a power source and look at the front panel LEDs. 4. 3 The Front Panel LEDs Figure 5 Front Panel LEDs The PWR LED turns on when you first connect the power. The SYS LED blinks while performing system testing and then stays on if the testing is successful. The WAN, LAN and MGMT LEDs turn on if the corresponding connections are properly made. Table 3 Front Panel LEDs LED PWR Green Red SYS Green COLOR STATUS Off On On Off On Blinking WAN 10/100 Off Green On DESCRIPTION The ZyWALL IDP is turned off. The ZyWALL IDP has a successful 10Mbps WAN connection. 9 ZyWALL IDP 10 Quick Start Guide Table 3 Front Panel LEDs LED COLOR STATUS Blinking Amber On Blinking LAN 10/100 Off Green On Blinking Amber On Blinking MGMT Green Off On Blinking Amber On Blinking DESCRIPTION The ZyWALL IDP is sending or receiving packets on the 10Mbps WAN connection. The ZyWALL IDP is sending or receiving packets on the 100Mbps WAN connection. The ZyWALL IDP is sending or receiving packets on the 10Mbps LAN connection. The ZyWALL IDP is sending or receiving packets on the 100Mbps LAN connection. The ZyWALL IDP has a successful 10Mbps Ethernet connection on the MGMT port. The ZyWALL IDP has a successful 100Mbps Ethernet connection on the MGMT port. The MGMT port is sending or receiving packets. 5 Accessing Your ZyWALL IDP Choose one of these methods to access (and configure) the ZyWALL IDP. Command line interface via the console port using terminal emulation software. To do this your computer must be in the same subnet as the ZyWALL IDP. The ZyWALL allows one management session at a time (console port, SSH (Secure Shell) or web configurator in that order of priority). Make sure there is not another management session already running before you try to start one. 12 ZyWALL IDP 10 Quick Start Guide Default IP address. Figure 7 Web Site Address 2. The default password ("1234") is already in the password field (in non-readable format). Click Login to proceed to a screen asking you to change your password. Click Reset to revert to the default password in the password field. Default password = 1234 Figure 8 Login 3. Enter a new password, retype it to confirm and click Apply; alternatively click Ignore if you do not want to change the password now. Change default password Figure 9 Change Password 13 ZyWALL IDP 10 Quick Start Guide 4. You should now see the web configurator HOME screen. Navigation panel Setup Wizard LOGOUT Figure 10 Home Screen Click Quick Setup to begin a wizard to help you configure your ZyWALL IDP for the first time. Click a link under SYSTEM in the navigation panel to configure general ZyWALL IDP features. Click IDP in the navigation panel to configure IDP-related ZyWALL IDP features. [. . . ] Cannot access the console port Make sure you have the physical connection properly set up as described in the hardware connections section. When configuring using the console port, you need a computer with a terminal emulation program configured to the following parameters: o o o Cannot access the ZyWALL IDP web configurator. 8 data bits, no parity, 1 stop bit, no flow control Make sure you are using the correct IP address to access the ZyWALL IDP. Connect to the ZyWALL IDP from the console port, log in to the command line interface and type "get system" to check the IP address of the ZyWALL IDP. [. . . ]