User manual ZYXEL ZYAIR B-420

[. . . ] ZyAIR B-420 Wireless LAN Ethernet Adapter and Bridge User's Guide Version 3. 50 September 2003 ZyAIR B-420 Wireless LAN Ethernet Adapter and Bridge Copyright Copyright © 2003 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. [. . . ] This key must be the same on the ZyAIR and the wireless stations to communicate. Both the ZyAIR and the wireless stations must use the same WEP key for data transmission. If you chose 64-bit WEP in the WEP Encryption field, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-F"). Key 1 to Key 4 If you chose 128-bit WEP in the WEP Encryption field, then enter 13 ASCII characters or 26 hexadecimal characters ("0-9", "A-F"). EXMAPLE Disable 1 Default Key 0x12345ab cde Enter "0x" before the key to denote a hexadecimal key. Don't enter "0x" before the key to denote an ASCII key. Authen. Method Press [SPACE BAR] to select Auto, Open System Only or Shared Key Only and press [ENTER]. Breathing LED Press [SPACE BAR] to select Yes or No and press [ENTER]. Output Power Edit Bridge Link Configuration Press [SPACE BAR] to select 11dBm, 13dBm, 15dBm or 17dBm and press [ENTER]. This field is only available when you select Bridge in the Operating Mode field. 17dBm N/A Auto When you have completed this menu, press [ENTER] at the prompt "Press ENTER to confirm or ESC to cancel" to save your configuration or press [ESC] to cancel and go back to the previous screen. 10-4 LAN Setup ZyAIR B-420 Wireless LAN Ethernet Adapter and Bridge 10. 3. 1 Configuring Bridge Link Follow the steps below to configure bridge link on your ZyAIR. Enter 5 to display Menu 3. 5 ­ Wireless LAN Setup. Menu 3. 5 - Wireless LAN Setup Operating Mode= Bridge ESSID= N/A Channel ID= CH06 2437MHz RTS Threshold= 2432 Frag. Threshold= 2432 WEP Encryption= Disable Default Key= N/A Key1= N/A Key2= N/A Key3= N/A Key4= N/A Authen. Method= N/A Breathing LED= Yes Output Power= N/A Edit Bridge Link Configuration= Yes Press ENTER to Confirm or ESC to Cancel: Figure 10-4 Menu 3. 5 Wireless LAN Setup Step 3. In the Operating Mode field, press [SPACE BAR] to select Bridge and press [ENTER]. Menu 3. 5. 4 ­ Bridge Link Configuration displays as shown next. Menu 3. 5. 4 - Bridge Link Configuration Active = Yes -----------------------------------------------------------------------------Peer Address = 00:a0:c5:55:97:50 ------------------------------------------------------------------------------ Press ENTER to Confirm or ESC to Cancel: Figure 10-5 Menu 3. 5. 4 Bridge Link Configuration LAN Setup 10-5 ZyAIR B-420 Wireless LAN Ethernet Adapter and Bridge The following table describes the fields in this menu. Table 10-3 Menu 3. 5. 4 Bridge Link Configuration FIELD Active Peer Address DESCRIPTION Press [SPACE BAR] to select Yes or No and press [ENTER]. Type the MAC address of peer device in valid MAC address format, that is, six hexadecimal character pairs, for example, 12:34:56:78:9a:bc. EXAMPLE Yes When you have completed this menu, press [ENTER] at the prompt "Press ENTER to confirm or ESC to cancel" to save your configuration or press [ESC] to cancel and go back to the previous screen. 10-6 LAN Setup ZyAIR B-420 Wireless LAN Ethernet Adapter and Bridge Chapter 11 SNMP Configuration This chapter explains SNMP configuration menu 22. 11. 1 About SNMP Simple Network Management Protocol is a protocol used for exchanging management information between network devices. Your ZyAIR supports SNMP agent functionality, which allows a manager station to manage and monitor the ZyAIR through the network. The ZyAIR supports SNMP version one (SNMPv1) and version two c (SNMPv2c). SNMP is only available if TCP/IP is configured. Figure 11-1 SNMP Management Model An SNMP managed network consists of two main components: agents and a manager. SNMP Configuration 11-1 ZyAIR B-420 Wireless LAN Ethernet Adapter and Bridge An agent is a management software module that resides in a managed device (the ZyAIR). [. . . ] 11-2 Trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3, 11-4 Trusted Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3 SSID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7, 4-10, 10-3 Subnet Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1, 10-2, 12-4 Subnet Masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2 Subnetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]