User manual ZYXEL PRESTIGE 662H

[. . . ] ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. ii Prestige 100 and 100IH ISDN Router and Router/Hub The declarations of CE marking: The Prestige 100 and 100IH has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU-TSS recommendation I. 420 (Basic Rate ISDN user access). The Council Directive 89/336/EEC of 3 May 1992 on the approximation of the laws of the member states relation to Electro Magnetic Compatibility. Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws of the Member States concerning telecommunication terminal equipment. [. . . ] nodename ________ ________ ________ ________ ________ ________ ________ Enter Node # to Edit: Figure 4-1 Menu 11 ­ Remote Node Setup When Submenu 11. 1 - Remote Node Profile appears, fill in the fields as described in the table below to define this remote profile. The Remote Node Profile Menu Fields table shows how to configure the Remote Node Menu. Menu 11. 1 - Remote Node Profile Rem Node Name= nodename Active= Yes Edit PPP Options= No Rem IP Addr= 0. 0. 0. 0 Edit IP= No Rem Node Name= remot Active= Yes Call Direction= Outg Call Direction= Outgoing Incoming: Telco Option: Rem Login= N/A Allocated Budget(min)= 0 Rem Password= N/A Period(hr)= 0 Rem CLID= N/A Transfer Type= 64K Call Back= N/A Nailed-Up Connection= No Outgoing: Session Options: My Login= ChangeMe Edit Filter Sets= No My Password= ******** Idle Timeout(sec)= 300 Authen= CHAP/PAP Pri Phone #= 1234 Sec Phone #= Enter here to CONFIRM or ESC to CANCEL: Incoming: Rem Login= N/A Rem Password= N/A Rem CLID= N/A Call Back= N/A Outgoing: My Login= ChangeMe My Password= ***** Authen= CHAP/PAP Pri Phone #= 1234 Sec Phone #= Figure 4-2 Menu 11. 1 Remote Node Profile 4-2 Remote Node Configuration Prestige 100 and 100IH ISDN Router and Router/Hub Table 4-1 Remote Node Profile Menu Fields Field Rem Node Name Description This is a required field [?]. This name must be unique from any other remote node name or remote dial-in user name. Inactive nodes are displayed with a minus sign (-) at the beginning of the name in Menu 11. l If this parameter is set to Both, your Prestige can both place and receive calls to/from this remote node. If set to Incoming, your Prestige will not place a call to this remote node. If set to Outgoing, your Prestige will drop any incoming calls from this remote node. Press space bar to toggle Yes/No Both Options Call Direction l Incoming l Outgoing Several other fields in this menu depend on this parameter. For example, in order to enable Callback, the Call Direction must be Both. Incoming: Rem Node Login Name Enter the login name that this remote node will use when it calls your Prestige. The login name in this field combined with the Rem Node Password will be used to authenticate this node. 64k/ Leased Yes/No Default = 0 Nailed-up Connection Session Option: Edit Filter Sets Session Option: Idle Timeout (sec) Default= No Default=300 secs for an unconfigured remote node. 0 secs means the remote node will never be automatically disconnected. Once you have completed filling in Menu 11. 1. 1 ­ Remote Node Profile, press [Enter] at the message [Press ENTER to Confirm. . . ] to save your configuration, or press [Esc] at any time to cancel. 4. 1. 2 Outgoing Authentication Protocol Generally speaking, you should employ the strongest authentication protocol possible, for obvious reasons. However, some vendor's implementation includes specific authentication protocol in the user profile. It will disconnect if the negotiated protocol is different from that in the user profile, even when the negotiated protocol is stronger than specified. If you encounter the case where the peer disconnects right after a successful authentication, please make sure that you specify the correct authentication protocol when connecting to such an implementation. Remote Node Configuration 4-5 Prestige 100 and 100IH ISDN Router and Router/Hub 4. 1. 3 PPP Multilink The Prestige uses the PPP Multilink Protocol (PPP/MP ) to bundle multiple links in a single connection to boost the effective throughput between two nodes. Due to the fragmentation/reconstruction overhead associated with MP, you may not get a linear increase in throughput when a link is added. The number of links in an MP bundle can be statically configured, or dynamically determined at runtime, as explained in the following section. 4. 1. 4 Bandwidth on Demand The Bandwidth on Demand (BOD) feature adds or subtracts links dynamically according to traffic demand. After the initial call, the Prestige uses BAP (Bandwidth Allocation Protocol) to ask the peer for additional telephone number if BACP (Bandwidth Allocation Control Protocol) is negotiated. Otherwise, the Prestige uses the statically configured (primary and secondary) telephone numbers of the remote node. The configuration of bandwidth on demand focuses on the Base Transmission Rate (BTR) and the Maximum Transmission Rate (MTR). The relationship between BTR and MTR are shown below: Table 4-2 BTR v MTR for BOD BTR & MTR Setting No. [. . . ] Dir Rate #call Max Min Total Enter Entry to Delete(0 to exit): Figure 10-18 Call History Table 10-6 Call History Fields Field Phone Number Dir Rate #call Description This is the telephone number of past incoming and outgoing calls. This is the number of calls made to or received from that telephone number. This is the total length of time of all the telephone calls to/from that telephone number. Max Min Total 10-20 System Maintenance Prestige 100 and 100IH ISDN Router and Router/Hub Chapter 11 Troubleshooting This chapter covers the potential problems you may run into and the possible remedies. After each problem description, some instructions are provided to help you to diagnose and to solve the problem. 11. 1 Problems Starting Up the Prestige Table 11-1 Troubleshooting the Start-Up of your Prestige Problem None of the LEDs are on when you power on the Prestige Corrective Action Check the connection between the AC adapter and the Prestige. [. . . ]