User manual ZYXEL PRESTIGE 2602R

[. . . ] Prestige 2602R Series ADSL VoIP IAD User's Guide Version 3. 40 2/2005 Prestige 2602R Series User's Guide Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. [. . . ] Each time you reload this page, the Prestige synchronizes the time with the time server. When you select None in the Use Protocol when Bootup field, enter the new time in this field and then click Apply. Click Cancel to begin configuring this screen afresh. Date Current Date New Date (yyyymm-dd) Time Current Time New Time Apply Cancel Chapter 10 Time and Date 108 Prestige 2602R Series User's Guide 109 Chapter 10 Time and Date Prestige 2602R Series User's Guide CHAPT E R 11 Remote Management Configuration 11. 1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers. When you configure remote management to allow management from the WAN, you still need to configure a firewall rule to allow access. You may manage your Prestige from a remote location via: · · · · Internet (WAN only) ALL (LAN and WAN) LAN only, Neither (Disable). When you Choose WAN only or ALL (LAN & WAN), you still need to configure a firewall rule to allow access. To disable remote management of a service, select Disable in the corresponding Server Access field. The Prestige automatically disconnects a remote management session of lower priority when another remote management session of higher priority starts. The priorities for the different types of remote management sessions are as follows. 1 Telnet 2 HTTP 11. 1. 1 Remote Management Limitations Remote management over LAN or WAN will not work when: · A filter in SMT menu 3. 1 (LAN) or in menu 11. 5 (WAN) is applied to block a Telnet, FTP or Web service. Chapter 11 Remote Management Configuration 110 Prestige 2602R Series User's Guide · You have disabled that service in one of the remote management screens. · The IP address in the Secured Client IP field does not match the client IP address. If it does not match, the Prestige will disconnect the session immediately. · There is already another remote management session with an equal or higher priority running. · There is a firewall rule that blocks it. 11. 1. 2 Remote Management and NAT When NAT is enabled: · Use the Prestige's WAN IP address when configuring from the WAN. · Use the Prestige's LAN IP address when configuring from the LAN. 11. 1. 3 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds). The Prestige automatically logs you out if the management session remains idle for longer than this timeout period. The management session does not time out when a statistics screen is polling. 11. 2 Telnet You can configure your Prestige for remote Telnet access as shown next. Figure 40 Telnet Configuration on a TCP/IP Network 11. 3 FTP You can upload and download Prestige firmware and configuration files using FTP. To use this feature, your computer must have an FTP client. 111 Chapter 11 Remote Management Configuration Prestige 2602R Series User's Guide 11. 4 Web You can use the Prestige's embedded web configurator for configuration and file management. See the online help for details. 11. 5 Configuring Remote Management Click Remote Management to open the following screen. Figure 41 Remote Management The following table describes the fields in this screen. Table 24 Remote Management LABEL Server Type Access Status Port DESCRIPTION Each of these labels denotes a service that you may use to remotely manage the Prestige. You may change the port number for a service in this field, but you must use the same port number to use that service for remote management. The default 0. 0. 0. 0 allows any client to use this service to remotely manage the Prestige. Type an IP address to restrict access to a client with a matching IP address. Click Cancel to begin configuring this screen afresh. Secured Client IP Apply Cancel Chapter 11 Remote Management Configuration 112 Prestige 2602R Series User's Guide 113 Chapter 11 Remote Management Configuration Prestige 2602R Series User's Guide CHAPT E R 1 2 Universal Plug-and-Play (UPnP) 12. 1 Introducing Universal Plug and Play Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. [. . . ] The facility is defined in the web MAIN MENU->LOGS->Log Settings page. The definition of messages and notes are defined in the various log charts throughout this appendix. The "devID" is the last three characters of the MAC address of the router's LAN port. The "cat" is the same as the category in the router's logs. Table 120 SIP Logs LOG MESSAGE SIP Registration Success by SIP:SIP Phone Number SIP Registration Fail by SIP:SIP Phone Number SIP UnRegistration Success by SIP:SIP Phone Number SIP UnRegistration Fail by SIP:SIP Phone Number DESCRIPTION The listed SIP account was successfully registered with a SIP register server. [. . . ]