User manual ZYXEL PRESTIGE 660H QUICK GUIDE

[. . . ] 2 LAN: Use an Ethernet cable to connect a computer to a LAN 10/100M port for initial configuration and/or Internet access. 3 POWER: Use the included power adaptor to connect the POWER socket to an appropriate power source (see the User's Guide for power adaptors specifications by region). After you've made the connections, push in the power button to turn on the Prestige. The PWR/SYS and/or WLAN LEDs then turn steady on if the testing is successful. [. . . ] To change the LAN settings, click Change LAN Configuration; otherwise click Save Settings to save the configuration and go to the final wizard screen. If you change the Prestige's LAN IP address, you must use the new IP address if you want to access the web configurator again. 4 Click Save Settings in the screen shown in step 3 to go to the final wizard screen. The Prestige automatically tests the connection to the computer(s) connected to the LAN ports. To test the connection from the Prestige to the ISP, click Start Diagnose. Otherwise click Return to Main Menu to go back to the main screen. 3 Wireless Configuration (P660HW series only) WPA-PSK encryption is preferred to WEP because it has user authentication and improved data encryption. If you don't have WPA-capable wireless clients, configure WEP encryption. 7 Prestige 660H/HW Series Quick Start Guide Note: Wireless clients and the Prestige must use the same SSID, channel ID, WEP or WPA-PSK key (if enabled). 1 Click the Wireless LAN link under Advanced Setup. Select Authentic ation Required, then select WPAPSK and then type a Preshared Key. 3 Click Advanced Setup, Wireless LAN, Wireless. In the ESSID field, enter up to 32 printable characters to uniquely identify the Prestige. If you didn't configure WPA-PSK, configure WEP in this screen (not visible if you've configured WPA-PSK). 8 Prestige 660H/HW Series Quick Start Guide 3. 1 OTIST Configure this screen only if you have OTIST-aware wireless clients. OTIST (One-Touch Intelligent Security Technology) allows you to transfer your Prestige's SSID and WEP or WPA-PSK security settings to wireless clients that support OTIST and are within transmission range. You can also choose to have OTIST generate a WPA-PSK key for you if you didn't configure one manually. To have OTIST automatically generate a WPA-PSK key select the Yes check box. If you manually configured a WEP key or a WPA-PSK key and you also selected this check box, then the key you manually configured is used. Note: The AP and wireless client(s) MUST use the same Setup key. In each wireless client ZyXEL utility, click the Adapter tab. Select the OTIST check box, enter the same Setup Key as your Prestige's and click Save. Note: You must click Start in the Prestige OTIST web configurator screen and in the wireless client(s) Adapter screen all within three minutes (at the time or writing). You can start OTIST in the wireless clients and Prestige in any order but they must all be within range and with OTIST enabled. 9 Prestige 660H/HW Series Quick Start Guide 4 NAT NAT (Network Address Translation - NAT, RFC 1631) means the translation of an IP address in one network to a different IP address in another. For example, you could translate one public IP address to multiple private IP addresses on your LAN (SUA Only). Select SUA Only if you have one public IP address and Full Feature if you have multiple public IP addresses (for address translation). If you have servers on your LAN, configure an SUA server set to have them visible to the outside. From the NAT - Mode screen click Edit Details and fill in the fields as shown. 5 Firewall The firewall is already enabled by default on the Prestige. No traffic can enter your LAN unless a request was generated on the LAN first. You can also disable the firewall here if you want. 10 Prestige 660H/HW Series Quick Start Guide 6 Troubleshooting PROBLEM CORRECTIVE ACTION None of the LEDs turn on when Make sure that you have the correct power adaptor connected to the Prestige, it you connect the Prestige's is plugged into an appropriate power source and the Prestige is turned on. Make sure your computer's IP address is in the same subnet as the Prestige's IP address (see Section 6. 1 on page 11). [. . . ] 3 Right-click Local Area Connection and then click Properties. 11 Prestige 660H/HW Series Quick Start Guide 4 Select Internet Protocol (TCP/IP) (under the General tab in Windows XP) and click Properties. 5 The Internet Protocol TCP/IP Properties screen opens (the General tab in Windows XP). 6 Select the Obtain an IP address automatically and Obtain DNS server address automatically options. 8 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. [. . . ]