User manual ZYXEL P-792H

[. . . ] Prestige 792H G. SHDSL 4-port Security Gateway Compact Guide Version 3. 40(BZ. 0) March 2004 Prestige 792H Table of Contents 1 Introducing the Prestige . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 1 Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. 1 Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This is necessary in order to communicate with the Prestige. Refer to your User's Guide for detailed IP address configuration for other Windows and Macintosh computer operating systems. 3. 4 Testing the Connection to the Prestige 1. In the Command Prompt window, type "ping" followed by a space and the IP address of the Prestige (192. 168. 1. 1 is the default). Click Reset or Cancel to begin configuring this screen afresh. 4. 3 Internet Access Using the Wizard Use the Wizard Setup screens to configure your system for Internet access settings and fill in the fields with the information in the Internet Account Information table. Your ISP may have already configured some of the fields in the wizard screens for you. In the Site Map screen click Wizard Setup to display the first wizard screen. 13 Prestige 792H Select Client if your Prestige will act as a client device or Server if your Prestige will act as a server. If you enable Rate Adaption, the Prestige will connect at the optimal transfer rate between the min and max rates below. If you disable Rate Adaption, it will attempt to connect at the maximum transfer rate configured. If that rate can't be attained, the connection will not be established. Next, select transfer rates from the Max Rate and Min Rate drop-down list boxes. For LAN-to-LAN applications make sure that your Prestige and its peer have the same Transfer Max Rate and the same Transfer Min Rate. Figure 6 Wizard Screen 1 If your Prestige is a server, then select the mode that applies to your region: ANSI (American National Standards Institute) and ETSI (European Telecommunications Standards Institute). If your Prestige is a client, select the same Standard Mode that the server side selects. Step 2. Click Next to go to the second Wizard screen. From the Mode drop-down list box, select Routing (default) if your ISP allows multiple computers to share an Internet account. Select the encapsulation type your ISP uses from the Encapsulation drop-down list box. Select the multiplexing method used by your ISP from the Multiplex drop-down list box. Enter the correct Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers supplied by your ISP in the VPI and VCI fields. Click Next. Figure 7 Wizard Screen 2 Step 3. The third wizard screen varies depending on what mode and encapsulation type you use. Configure the fields and click Next to continue or Back to go to the previous screen. See the first screen below, Internet Connection with PPPoA, for explanations of the following fields: User Name, Password, IP Address, Connection, and Network Address Translation. 14 Prestige 792H Enter the user name and password exactly as your ISP assigned them. Select Obtain an IP Address Automatically if you have a dynamic IP address; otherwise select Static IP Address and type your ISP assigned IP address in the text box below. Select Connect on Demand when you don't want the connection up all the time and specify an idle time-out period (in seconds) in the Max. Select Nailed-Up Connection when you want your connection up all the time. The Prestige will try to bring up the connection automatically if it is disconnected Figure 8 Internet Connection with PPPoA From the Network Address Translation drop-down list box, select SUA Only, Full Feature or None. [. . . ] This field shows you if a log is created for packets that match the rule (Match), don't match the rule (Not Match), both (Both) or no log is created (None). Use the drop-down list box to select the number of the rule you want to move. Use the drop-down list box to select to where you want to move the rule. Click Move to move the rule. Source IP Destination IP Service Action Log Rules Reorder To Rule Number Move Follow these directions to create a new rule. [. . . ]