User manual ZYXEL P-630-S

[. . . ] P-630-S Series ADSL USB Modem User's Guide Version 1. 0 7/2005 P-630-S User's Guide Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. [. . . ] 3 Connect the side labeled "Line" to the telephone wall jack. Figure 5 Splitter 16 Chapter 2 Hardware Overview P-630-S User's Guide 2. 3. 2 Telephone Microfilters You may opt to buy a telephone microfilter to install between the wall jack and your telephone(s). A microfilter acts as a low-pass filter, for your telephone, to ensure that ADSL transmissions do not interfere with your telephone voice transmissions. 1 Connect a phone cable from the wall jack to the single jack end of the Y- Connector. 2 Connect a cable from the double jack end of the Y-Connector to the "wall side" of the microfilter. 3 Connect another cable from the double jack end of the Y-Connector to the Prestige. 4 Connect the "phone side" of the microfilter to your telephone as shown in the following figure. Figure 6 Microfilter Chapter 2 Hardware Overview 17 P-630-S User's Guide 18 Chapter 2 Hardware Overview P-630-S User's Guide CHAPTER 3 Modem Setup This chapter shows you how to set up your modem for ADSL Internet access. 3. 1 Needed Information Fill in the table below with information from your Internet Service Provider (ISP) and telephone company before installation. You may not need to fill in every blank. Table 2 Needed Information REQUIRED INFORMATION Protocol: Bridge, PPPoA or PPPoE. VPI: The Virtual Path Identifier number identifies a bundle of virtual channels. VCI: The Virtual Channel Identifier number identifies a logical connection between end stations. Modulation: Your ISP will tell you which type of ADSL modulation it uses. · ANSI T1. 413 Issue 2 · ITU G. 992. 1 (G. dmt) · ITU G. 992. 2 (G. lite) User Name / Password: Lets your ISP know which account you are logging into and protects your account from unauthorized users. IP Address (if given) FILL IN THE BLANKS Your modem supports Bridge, PPPoA (Point to Point Protocol over ATM) and PPPoE (Point to Point Protocol over Ethernet) encapsulation. Your modem supports both LLC and VCMUX. Chapter 3 Modem Setup 19 P-630-S User's Guide 3. 2 PPP over Ethernet PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP. The Prestige bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your computer to an ATM PVC (Permanent Virtual Circuit) which connects to ADSL Access Concentrator where the PPP session terminates. For more information on PPPoE, see the appendices. 3. 3 PPPoA PPPoA stands for Point to Point Protocol over ATM Adaptation Layer 5 (AAL5). The Prestige encapsulates the PPP session based on RFC1483 and sends it through an ATM PVC (Permanent Virtual Circuit) to the Internet Service Provider's (ISP) DSLAM (digital access multiplexer). Refer to RFC 1661 for more information on PPP. 3. 4 Multiplexing There are two conventions to identify what protocols the virtual circuit (VC) is carrying. Be sure to use the multiplexing method required by your ISP. 3. 4. 1 VC-based Multiplexing In this case, by prior mutual agreement, each protocol is assigned to a specific virtual circuit; for example, VC1 carries IP, etc. VC-based multiplexing may be dominant in environments where dynamic creation of large numbers of ATM VCs is fast and economical. 3. 4. 2 LLC-based Multiplexing In this case one VC carries multiple protocols with protocol identifying information being contained in each packet header. Despite the extra bandwidth and processing overhead, this method may be advantageous if it is not practical to have a separate VC for each carried protocol, for example, if charging heavily depends on the number of simultaneous VCs. 3. 5 VPI and VCI Be sure to use the correct Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers assigned to you. The valid range for the VPI is 0 to 255 and for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). Please see the appendix for more information. 20 Chapter 3 Modem Setup P-630-S User's Guide 3. 6 Configuration Wizard The following sections show you how to confiure your Prestige in Windows and Mac. 3. 6. 1 Windows Screens for Windows XP are shown in this section unless otherwise specified. [. . . ] You can also open Network Connections, right-click a network connection, click Status and then click the Support tab. Macintosh OS 8/9 1 Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel. Appendix A Setting up Your Computer's IP Address 51 P-630-S User's Guide Figure 24 Macintosh OS 8/9: Apple Menu 2 Select Ethernet built-in from the Connect via list. Figure 25 Macintosh OS 8/9: TCP/IP 3 For dynamically assigned settings, select Using DHCP Server from the Configure: list. 52 Appendix A Setting up Your Computer's IP Address P-630-S User's Guide 4 For statically assigned settings, do the following: · · · · From the Configure box, select Manually. Type the IP address of your Prestige in the Router address box. 5 Close the TCP/IP Control Panel. 7 Turn on your Prestige and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the TCP/IP Control Panel window. Macintosh OS X 1 Click the Apple menu, and click System Preferences to open the System Preferences window. Figure 26 Macintosh OS X: Apple Menu 2 Click Network in the icon bar. Click the TCP/IP tab. 3 For dynamically assigned settings, select Using DHCP from the Configure list. Appendix A Setting up Your Computer's IP Address 53 P-630-S User's Guide Figure 27 Macintosh OS X: Network 4 For statically assigned settings, do the following: · · · · From the Configure box, select Manually. [. . . ]