User manual ZYXEL P-334WT

[. . . ] It returns the Prestige to the factory defaults (password is 1234, LAN IP address 192. 168. 1. 1. See your User's Guide for details). 3 P-334WT 2. 2 Front Panel LEDs The PWR LED blinks while performing system testing and then stays on if the testing is successful. The LAN, and WAN LEDs turn on if they are properly connected. LED PWR Amber Green STATUS COLOR Off On On Blinking LAN 1- 4 Green Off On Blinking Amber On DESCRIPTION The Prestige is not receiving power. The Prestige is sending/receiving data The Prestige has a successful 100Mb Ethernet connection. 4 P-334WT LED STATUS COLOR Blinking WAN Green Off On Blinking Amber On Blinking WLAN Green Off On Blinking DESCRIPTION The Prestige is sending/receiving data The WAN connection is not ready, or has failed. [. . . ] Click WIZARD to begin a series of screens to help you configure your Prestige for the first time. Click the BM SETUP to begin a series of screens to help you configure media bandwidth management on your Prestige. Click a link under MAIN MENU in the navigation panel to configure that Prestige feature. 10 P-334WT Click MAINTENANCE in the navigation panel to see Prestige performance statistics, upload firmware and back up, restore or upload a configuration file. The Prestige automatically logs you out if it is left idle for five minutes; press ENTER to display the Login screen again and then log back in. This idle timeout timer is one of the many Prestige features that you may edit using the web configurator. WIZARD BANDWIDTH MANAGEMENT WIZARD Navigation panel LOGOUT 4. 2 Internet Access Using the Wizard The wizard consists of a series of screens to help you configure your Prestige for wireless stations to access your wired LAN. Use the following buttons to navigate the Wizard: Back Next Click Back to return to the previous screen. Click Next to continue to the next screen. No configuration changes will be saved to the Prestige until you click Finish. 1. Click Wizard Setup in the main menu to display the first wizard screen. 11 P-334WT System Name is a unique name to identify the Prestige in an Ethernet network. The Domain Name entry is what is propagated to the DHCP clients on the LAN. If you leave this blank, the domain name obtained by DHCP from the ISP is used. Click Next to continue. 2. Use the second wizard screen to set up the wireless LAN. Name(SSID) is a unique name to identify the Prestige in the wireless LAN. The range of radio frequencies used by IEEE 802. 11b/g wireless devices is called a channel. Select a channel ID that is not already in use by a neighboring device. Click None, Basic(WEP) or Extend(WPA-PSK) from the drop-down list box as the level of wireless security. If you do not enable any wireless security on your Prestige, your network is accessible to any wireless networking device that is within range. Choose Basic(WEP) security if you want to configure WEP Encryption parameters. The third screen varies depending on which security level you select. The wireless stations and Prestige must use the same SSID, channel ID and WPAPSK (if WPA-PSK is enabled), WEP encryption key (if WEP is enabled) for wireless communication. 3. Choose Basic(WEP) security in the previous screen to setup WEP Encryption parameters. 12 P-334WT WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. The higher the WEP Encryption, the higher the security but the slower the throughput. Use Passphrase to automatically generate a key or manually enter a key in one of the Key 1~ 4 fields. Select 64-bit, 128-bit or 256-bit from the WEP Encryption drop-down list. You can generate or manually enter a WEP key by either: Entering a Passphrase (up to 32 printable characters) and clicking Generate. Or Entering a manual key in a Key field and selecting ASCII or Hex WEP key input method. 4. Choose Extend(WPA-PSK) security in the second wizard screen to set up a Pre-Shared Key. Pre-Shared Key Type a pre-shared key to have a more secure wireless connection than WEP encryption. You can set up the most secure wireless connection by configuring WPA in the advanced wireless screen. [. . . ] Rear Panel section for details. CORRECTIVE ACTION Ping the Prestige from a LAN computer. Make sure your computer Ethernet card is installed and functioning properly. Cannot ping any computer on the LAN. If the 10/100M LAN LEDs are off, check the cable connections between the Prestige and your LAN computers. Verify that the IP address and subnet mask of the Prestige and the LAN computers are in the same IP address range. Cannot get a WAN IP address from the ISP. The WAN IP is provided after the ISP verifies the MAC address, host name or user ID. Find out the verification method used by your ISP and configure the corresponding fields. [. . . ]