User manual ZYXEL P-2602R-D QUICK GUIDE V3.40

[. . . ] 4 PHONE 1-2: Use telephone cables (and any telephone adaptors provided with your P-2602RL-DxA) to connect your telephones to these ports. 5 POWER: Use the power adaptor provided with your P-2602RL-DxA to connect an appropriate power source to this socket. Note: If you are using T-ISDN (UR-2), connect the green wire to a TAE connector before connecting it to a telephone wall jack or the telephone splitter's TEL or PHONE jack. 3 P-2602R/RL-DxA Quick Start Guide 6 Push in the POWER button. · The POWER light blinks during start-up and is green once the P-2602RL-DxA is ready. · Each ETHERNET light turns on if the corresponding ETHERNET port is properly connected. [. . . ] · The DSL light stays on if a physical connection with the ISP is established. · The PHONE lights stay on when your SIP account is registered and they blink if the receiver is off hooked. If PHONE 1 or PHONE 2 light is on, skip to Section 4 to see how to make calls through the Internet. If the INTERNET light comes on but the PHONE lights are off, go to Section 3. 2 and use the VOICE OVER INTERNET SETUP wizard. If the INTERNET light is off but the DSL light is on, go to Section 3. 1 and use the INTERNET SETUP wizard to configure your Internet access settings. 3 Initial Configuration Open your web browser, and go to http://www. zyxel. com. If any other screens appear, follow the directions in the screen. 6 P-2602R/RL-DxA Quick Start Guide If http://www. zyxel. com opens correctly, your Internet access is ready. Then, click Login. If your browser cannot find this screen, make sure your browser is configured correctly. 3 Type (and retype) a new password and click Apply. 7 P-2602R/RL-DxA Quick Start Guide 4 Click Go to Wizard setup. Then, click Apply. 3. 1 Internet Setup Note: You should have the information provided by your ISP. 1 Click INTERNET SETUP. Wait while the P-2602R/RL-DxA tries to detect your Internet connection. If the P-2602R/RL-DxA cannot detect your Internet connection, follow the directions in the screens. Keep the default settings if your Internet service provider did not provide some information. When your Internet connection is setup correctly, the INTERNET light should be green, and the following screen appears. 8 P-2602R/RL-DxA Quick Start Guide 2 Confirm that your Internet setup settings are correct and click Return to Wizard Main Page to continue with VoIP setup. 3. 2 VoIP Setup Note: You should have the information provided by your VoIP service provider. Click VOICE OVER INTERNET SETUP. Keep the default settings if your VoIP service provider did not provide some information. If you have a SIP account like 1234567@VoIPprovider. com, the SIP Number is 1234567, and the SIP Service Domain is VoIP-provider. com. When you are done, the PHONE light should be on. Click Exit to close the wizard and the main screen appears. 3. 3 Regular Phone Line Setup ("L" models) When one of your VoIP accounts is registered, the P-2602RL-DxA normally uses the Internet (not the regular phone line) to make phone calls. Follow the directions in this section to make sure you can also use the regular phone line while one of your VoIP accounts is registered. 9 P-2602R/RL-DxA Quick Start Guide Note: When the ZyXEL Device does not have power, only the phone connected to the PHONE 2 port can be used for making calls. Ensure you know which phone this is, so that in case of emergency you can make outgoing calls. In the main screen, click VoIP > PSTN Line. PSTN Line Pre-fix Number: Enter 1 - 7 numbers you dial before you dial the phone number, if you want to make a regular phone call while one of your SIP accounts is registered. These numbers tell the ZyXEL device that you want to make a regular phone call. Relay to PSTN Line: Enter phone numbers for regular phone calls (that do not use the Internet) that you always want to dial without the prefix number. Click Apply. 4 Phone Calls Follow these directions to make calls over the Internet. [. . . ] For example, if your account has a user name and password, make sure you type it correctly. In addition, if you are not sure which encapsulation your ISP uses, contact your ISP. 3 If you are using a new Internet account, contact your ISP to make sure it is active. 4 If you still have problems, see Troubleshooting in the User's Guide. [. . . ]