User manual ZYXEL P-2002L

[. . . ] Prestige 2002 Series VoIP Analog Telephone Adaptor Quick Start Guide Version 3. 60 July 2004 Prestige 2002 Series 1 Introducing the Prestige The Prestige 2002 is a VoIP (Voice over IP) analog telephone adaptor. It lets you use a traditional analog telephone to send voice over the Internet. You can call landline or mobile telephones as well as IP telephones (depending on your VoIP service provider). Calls received from IP telephones work exactly as you would expect from the traditional telephone service. [. . . ] Press ENTER and the following screen displays. C:\>ping 192. 168. 5. 1 Pinging 192. 168. 5. 1 with 32 bytes of data: Reply Reply Reply Reply from from from from 192. 168. 5. 1: 192. 168. 5. 1: 192. 168. 5. 1: 192. 168. 5. 1: bytes=32 bytes=32 bytes=32 bytes=32 time=10ms time<10ms time<10ms time<10ms TTL=254 TTL=254 TTL=254 TTL=254 Ping statistics for 192. 168. 5. 1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 10ms, Average = 2ms Your computer can now communicate with the Prestige. 4 Configuring Your Prestige The web configurator is an HTML-based management interface that allows easy Prestige setup and management via Internet browser. Use Internet Explorer 6. 0 and later or Netscape Navigator 7. 0 and later versions with JavaScript enabled. See your User's Guide for background information on all Prestige features. 4. 1 Accessing Your Prestige Via Web Configurator 1. This is because by default, the Prestige is set to receive a dynamically assigned IP address and thus has no IP address. For initial configuration, use the Prestige's management IP address. Whether you use the Prestige's management IP address or its actual IP address (after it receives one), make sure that your computer's IP address is in the same subnet. 10 Prestige 2002 Series If your LAN has multiple Prestige 2002s, you can disconnect your Prestige 2002's LAN port to avoid accessing the wrong Prestige 2002 via the management IP address. Reconnect your Prestige 2002's LAN port after the Login screen displays. Management IP Address 2. In some versions, the default password appears automatically - if this is the case, click Login. 3. You should see a screen asking you to change your password (highly recommended) as shown next. Type a new password (and retype it to confirm) and click Apply or click Ignore. 4. Click the HELP icon (located in the top right corner of most screens) to view online help. Click a link under CONFIGURATION to configure Prestige features. 11 Prestige 2002 Series Click a link under MAINTENANCE to see Prestige performance statistics, upload firmware and back up, restore or upload a configuration file, or restart the Prestige. Click LOGOUT in the navigation panel when you have finished a Prestige management session. Navigation panel LOGOUT The Prestige automatically logs you out if the management session is idle for five minutes. Simply log back in if this happens to you. 4. 2 Common Screen Command Buttons The following table shows common command buttons found on many web configurator screens. Apply Reset/Cancel Click Apply to save your changes back to the Prestige. Click Reset or Cancel to begin configuring this screen afresh. 5 Initial Configuration This section describes how to configure your device's Ethernet interface and Voice over IP settings. 12 Prestige 2002 Series 5. 1 ETHERNET Configuration Click ETHERNET in the navigation panel to display the following screen. Use this screen to configure the Prestige's Ethernet interface with the information in the Ethernet Interface Information table. For example, if 1122334455@VoIP-provider. com was your SIP URI, "VoIP-provider. com" is the SIP service domain. You can configure the Prestige 1 to use multiple SIP accounts. If you were given a SIP Local Port number, enter it; otherwise leave it set to the default. Type the IP address of the VoIP service provider's SIP server in the SIP Server Address field. If you were given a SIP Server Port number, enter it; otherwise leave it set to the default. If your VoIP service provider gave you a registrar server address and port, enter them in the REGISTER Server Address and REGISTER Server Port fields. If you were not given a registrar server address and port, enter the address and port from the SIP Server Address and SIP Server Port fields again here. [. . . ] If your ISP provides the IP address of a STUN server, click VoIP and then Advanced to open this screen. 17 Prestige 2002 Series Remember that you can configure the Prestige to use multiple SIP accounts. Type the IP address of the VoIP service provider's STUN server in the Server Address field. If you were given a STUN port number, enter it in the Server Port field; otherwise leave it set to the default. See the User's Guide for more about STUN and NAT. 7. 1 Test Your Configuration If you have configured the Prestige correctly, the PWR/VoIP LED should be on with an orange color. [. . . ]