User manual ZYXEL P-2000W

[. . . ] With the battery's CE label facing up, put the end with the contacts in first and press the battery down into place. 3 Place the battery cover back on. Slide the cover towards the top until it clicks into place. 4 Remove the gray rubber cover from the bottom of your phone. Use the included power adaptor (use only this adaptor) to connect the phone to an appropriate power outlet. The OK key turns on bright red. Note: Charge the battery for two hours before using your Prestige. The battery provides approximately 3. 5 hours of talk time and 21-22 hours of standby time when fully charged. [. . . ] Use the up and down arrows to select capital letters (A), lowercase letters (a), numbers (1), or symbols (@). PPPoE Name my_username Ok Aa1@ Clear 9 P-2000W_V2 Quick Start Guide 4 Use the keypad to enter your PPPoE name. Use the Power/End key to clear PPPoE Name the default text and remove typos. For example, to enter a lowercase "b", press the down arrow key to select lowercase mode (a), then press the "2" key twice. PPPoE Name Select 7 Select a keypad mode and use the keypad to enter your PPPoE password. 8 Press the Right key twice to save your settings and return to the main screen. PPPoE Pwd my_password Ok A a 1@ Clear Back Clear 4 Setting the Prestige to Use Your Voice Account Use these sections to register your Prestige with your voice service provider's SIP server. 4. 1 Configuring Registrar Server Settings Configure the Registrar settings to have the Prestige register with your provider's SIP registrar server. Note: If you have no registrar server information, use the SIP server IP address and port number. 1 In the main screen, press the Left key to enter the menus. 12:00 ZyXEL Not registered Menu 2 Use the down arrow key to scroll to SIP Settings and press the OK key. Wireless Select Back Names 10 P-2000W_V2 Quick Start Guide 3 Scroll to Registrar and press the OK key. Expiry Time Select 5 You will enter your registrar server's IP address or domain name here. The bottom center of the screen shows the keypad mode Aa1@, with the A mode highlighted. Use the up and down arrows to select capital letters (A), lowercase letters (a), numbers (1), or symbols (@). 6 Use the keypad to enter your registrar server's IP address or domain name. For example, to enter a lowercase "b", press the down arrow key to select lowercase mode (a), then press the "2" key twice. Registrar IP mysip. proxy. com Ok A a 1@ Clear Back Back Registrar IP mysipprovider. com Ok 2. Registrar IP Select Back A a 1@ Clear 8 Use the keypad to enter the registrar server's listening port number if you were Port given one. Ok Aa 1 @ Clear 11 P-2000W_V2 Quick Start Guide 10 Scroll to Expiry Time and press the OK key. Port Select 11 Use the keypad to enter the expiration time if you were given one to use. Use Expiry Time the Power/End key to clear the default text and remove typos. Leave the 300 default expiration time if you were not given one to use. Ok Aa 1 @ 12 Stay in the SIP Settings menu and continue with the next section. Back Clear 4. 2 Configuring Outbound Proxy Server Settings If your voice service provider gave you an outbound proxy server address and port, you can enter them here. You only need to configure the Prestige to use an outbound proxy server if your LAN is behind a NAT router that does not support SIP. [. . . ] The signal quality is low or the Prestige cannot connect to the wireless network. Connect to another wireless network or move your Prestige closer to the wireless network's access point. There may be radio interference (for example a microwave or another wireless network using the same channel). Relocate or reduce the radio interference. 18 P-2000W_V2 Quick Start Guide PROBLEM "Net Fail! [. . . ]