User manual ZYXEL OMNI 56K USB

[. . . ] User's Guide for ZyXEL Omni 56K USB Modem ZyXEL TOTAL INTERNET ACCESS SOLUTIONS ZyXEL Communications Corporation User's Guide for ZyXEL Omni 56K USB Modem ZyXEL Omni 56K USB Modem Trademarks: Product and corporate names mentioned in this publication are used for identification purposes only and may be properties of their respective owners. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, guide, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Disclaimer: ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. [. . . ] (Ignored if in non-FSK or half-duplex operation. ) S10= Sets duration, in tenths of a second, modem waits after loss of carrier before hanging up. S11= Sets duration and spacing, in milliseconds of dialed Touch-Tones. +060 +002 +006 +007 +070 Table 25. Extended S-Registers "ATSn=x" Ref. +000 COMMAND Bit dec hex FUNCTION AND DESCRIPTION S13= Bit dec hex Bit-mapped register. 1 2 2 Capture modem manufacturer information during V. 42 handshake, can be displayed at ATI2 <Last Speed/Protocol> line if available (`Flash' or `ZyXEL' 5-22 User's Guide for ZyXEL Omni 56K USB Modem COMMAND S14= FUNCTION AND DESCRIPTION stands for ZyXEL connection). bit dec hex Bit-mapped register: 1 0 0 Grant Remote Digital Loop-back test request. +002 &T4 &T5* +066 S15= * * *C0* *C1 *C2 *C3 Z0 Z1 Z2* +000 &T0 &T1 &T3 &T6 &T7 &T8 +022 *Pn D DR +000 S16= S17= S18= S19= S20= +000/&Nn +001 5-23 User's Guide for ZyXEL Omni 56K USB Modem dec hex FUNCTION AND DESCRIPTION 2 2 76800 bps 3 3 57600 bps 4 4 38400 bps 5 5 19200 bps 6 6 16800 bps 7 7 14400 bps 8 8 12000 bps 9 9 9600 bps 10 A 7200 bps 11 B 4800 bps 12 C 2400 bps 13 D 1200 bps 14 E 460800 bps 15 F 300 bps 16 10 307200 bps 17 11 153600 bps 18 12 102400 bps 20 14 61440 bps 21 15 51200 bps 22 16 624000 bps 24 18 124800 bps 25 19 62400 bps 26 1A 41600 bps 27 1B 31200 bps 28 1C 24960 bps 29 1D 20800 bps 46 2E 921600 bps NOTE: Only speeds up to S20=15 are supported by auto-speed detection. 0 0 0 Maintain a non-error control connection when modem error control handshake fails. (Default) 1 1 Drop connection when modem error control handshake fails. 6 6 Speaker is ON after last digit is dialed out until carrier is detected. COMMAND Bit Ref. +178 *E0 *E1 M0 M1* M2 M3 5-24 User's Guide for ZyXEL Omni 56K USB Modem COMMAND Bit dec 3 0 8 4 0 16 5 0 32 6-7 0 64 128 hex 0 8 0 10 FUNCTION AND DESCRIPTION DSR is always ON. 80 108. 2 Data Terminal Ready, DTR OFF causes the modem to hang up and return to command state. (Default) C0 108. 2, DTR OFF causes the modem to hang up and reset the modem to profile 0 after DTR dropped. 0 Pulse dial make/break ratio = 39% / 61% (Default) 4 Pulse dial make/break ratio = 33% / 67% 0 ATX0 (See result code table) 8 ATX1 10 ATX2 18 ATX3 20 ATX4 28 ATX5, error control result code is enabled. &S0 &S1 &C0 &C1 &R0 &R1 &D0 &D1 &D2 192 S23= bit 0 1 2 3-5 dec 0 1 0 2 0 4 0 8 16 24 32 40 48 56 0 64 0 128 dec 16112 &D3 +105 E0 E1 T P &P0 &P1 X0 X1 X2 X3 X4 X5 X6 X7 V0 V1 Q0 Q1 L0-7 6 7 S24= bit 6-4 5-25 User's Guide for ZyXEL Omni 56K USB Modem S25= 0 to 255 0-FF Specify the time delay that DTR signal needs to be OFF before it is recognized, in 10 ms units. 0 to 0-FF Set the delay, in 10 millisecond units between the 255 RTS and modem's CTS response in synchronous mode. 1 1 MNP4 + MNP3 (see also S41. 0) 2 2 MNP4 + MNP5 (see also S38. 5, S41. 0) 3 3 V. 42+MNP4 4 4 V. 42 + V. 42bis (compatible with &K2) (Default) 0 0 Flow control disabled. 128 80 Adaptive rate (auto fall-back/forward) when signal quality changes. (See also S18, S44b6) 1 64 DTE/DCE rate is fixed at the DTE setting, range from 300 to 460. 8 Kbps. (Default, also see S18, S44b6) 0 to 3 0 to 3 Set default dial phone number pointer, use AT&Zn=s to store phone numbers in EEPROM. +000 S26= +000 &Rn S27= Bit 0-2 +156 &K0 &K1 &K2 &K3 &K4* &H0 &H3 &H4 &H5 *Q0 *Q1 *Q2 *Q3 +068 &Y0 &Y1 &Y2 &G0 &G1 &G2 &B0 &B1 +000 *D +017 +019 +032 3-5 6-7 S28= bit 2-3 4-5 6 S29= S31= S32= S35= bit 5-26 User's Guide for ZyXEL Omni 56K USB Modem 1 3 5 7 2 8 32 128 2 8 20 80 Disable aborting from terminal during modem handshaking. (Default) Enable extended numerical result codes from 50 to 65 when an error corrected connection is made. Type 2* security, with password check and call back; call back number from remote. [. . . ] Software that pretends to be (emulates) a physical terminal and allows you to type commands to a computer somewhere else. A token is a re-encoding of information in less bits; basically an abbreviation. Universal Asynchronous Receiver and Transmitter; a special IC chip which controls the serial port. (Uniform Resource Locator) URL is an object on the Internet or an intranet that resides on a host system. [. . . ]