User manual ZYXEL NETATLAS ENTERPRISE QUICK START GUIDE V1.02

[. . . ] The NetAtlas Enterprise Ethernet Switch Manager will be referred to as the EMS in this guide. 2 System Requirements These are the system requirements for the Windows version of the EMS. · CPU: Intel Pentium 4, 1. 6 GHz or above · Memory (RAM): 1 GB or more · Hard Disk free space: 20 GB or more · Screen Resolution: 1024x768 pixels · Ethernet Adaptor: 10/100 Mbps · Operating System: Windows 2000 (with service pack 1), Windows XP or Windows Server 2003 and all using NTFS file system. · Castle Rock's SNMPc 6. 2. 1 EMS Installation Overview The following gives an overview of what you need to do to install the EMS: 1 Install SNMPc. [. . . ] Conversely, clear this check box if you do not wish SNMPc to automatically start each time you turn on your computer. 5 Adding MIBs The Management Information Base (MIB) is designed for holding management information on systems (such as the switch that the standard MIB does not include). 1 From the SNMPc Network Manager main screen, click Config, MIB Database. 2 In the Compile Mibs screen that displays, scroll down to the bottom of the Mibs to Compile list box and click Add. Note: If you have uninstalled an earlier version of the EMS, you must remove zyxel. mib first. 3 Select the following MIBs in the Add Mibs list box: · · · · · · · rfc2674. mib rfc2925. mib rfc3291. mib rfc3621. mib OSPF-MIB. mib zyxel-es3124. mib zyxel-es3124pwr. mib. 5 NetAtlas Enterprise Quick Start Guide · · · · · · zyxel-es2024a. mib zyxel-gs2024. mib zyxel-gs4024. mib zyxel-gs4012f. mib zyxel-es2108. mib zyxel-es2108g. mib Note: You MUST add the MIBs in the order listed above. 4 Click OK. 7 Finally click Done in the Compile Mibs screen. 6 Finding your Switch The SNMPc Network Manager can find new devices automatically using auto-discovery (enabled by default) or you will have to add device(s) manually. 6. 1 Device Auto-Discovery 1 To enable auto-discovery and then find your device, click Config, Discovery/Polling. Double-click the device icon to access the EMS. 6 NetAtlas Enterprise Quick Start Guide 6. 2 Add Device(s) Manually If you have disabled auto-discovery, follow the steps below to add your device(s) manually. 2 In the MAP Object Properties screen, enter a descriptive device name and IP address for the device and then click OK. 7 Using SNMP Check that you are using SNMP Version 2c (SNMPv2c). If you are not using SNMPv2c, you must uninstall any previous versions and install SNMPv2c. 3 Set the specified fields in the Map Object Properties screen exactly as shown in the figure. Note: For security purposes, it is strongly recommend to change the Read Community and Read/Write Community defaults. Write down this information in a secure place so you will not forget it later. 7 NetAtlas Enterprise Quick Start Guide 4 Click OK. After the device has been found, the icon and label appear in the network manager view window. 5 Right-click on the device icon to view a set of SNMPc network manager shortcuts. Click Properties to verify the information you entered in the previous step. If it does not, click Start (or start), Programs, PostgreSQL 8. 0 and then click Start service. 8 Accessing the EMS Follow the steps below to access the EMS. 1 In the SNMPc main screen, double-click the device icon to view the Switch Manager. Click the Switch Manager icon to access the main EMS configuration screen. 9 Troubleshooting 1 SNMPc, EMS and/or PostgreSQL will not install properly · Make sure that the computer on which you want to install the SNMPc, EMS and PostgreSQL meets the minimum hardware and software requirements. · To install PostgreSQL, make sure your computer is using NTFS file system. 8 NetAtlas Enterprise Quick Start Guide · Shut down any running services or applications which may affect the installation. · Remove any previous versions of PostgreSQL and SNMP software from your computer. [. . . ] Double-click Administrative Tools. 9 NetAtlas Enterprise Quick Start Guide 2 Double-click Data Source (ODBC). In the User DNS screen, select PostgreSQL and click Configure. 4 The PostgreSQL ODBC Driver Setup screen displays. Configure the Database, Server and Port fields exactly as shown in the figure. [. . . ]