User manual ZYXEL IES-5000

[. . . ] IES-5000 Series Integrated Ethernet Switch User's Guide Version 3. 01 8/2007 Edition 1 www. zyxel. com About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to install and maintain the IES-5000 series Integrated Ethernet Switch. This User's Guide gives hardware installation, connection and maintenance instructions. Related Documentation · Line Card User's Guides These User's Guides provide hardware connection details and explain how to configure and manage the individual line cards. · Management Switch Card User's Guide This User's Guide provides hardware connection details, and configuration and management instructions for the management switch card. · Supporting Disk Refer to the included CD for support documents. [. . . ] 2 Grasp the center of the front panel of the card with one hand and place the other hand under the card to support it. 3 Insert the card into the slot and push it in until the front panel of the card is flush with the front panel of the splitter chassis. 4 Tighten the two thumbscrews. Figure 13 Installing a Splitter Chassis Card Figure 14 Tightening Splitter Chassis Card Thumbscrews 34 IES-5000 Series User's Guide Chapter 2 Hardware Installation and Connections 2. 3. 4 Removing a Splitter Chassis Card Use the following procedure to remove a splitter card from the splitter chassis. Grasp the handles on the front panel of the card and start to pull the card out. After you have the card partially out of the chassis, place one hand under the card to support it. 5 Slide the card out of the slot. Figure 15 Loosening Splitter Chassis Card Thumbscrews IES-5000 Series User's Guide 35 Chapter 2 Hardware Installation and Connections Figure 16 Removing a Splitter Chassis Card 2. 4 Making Card Connections The following describes how to connect the line cards to the splitter chassis cards. For the management switch card, refer to the card's User's Guide for instructions on making the connections. 2. 4. 1 48-port Line Card Connections Use a Telco-50 cable to connect the line card's front panel Telco-50 connector to the corresponding splitter card's front panel Telco-50 connector. Make sure that you use the appropriate length Telco-50 cables with the line cards; using cables of the wrong length blocks access to other cards. See the specifications appendix for the lengths of ZyXEL's optional Telco-50 cables. Use a long Telco-50 cable to connect a line card's 1-24 Telco-50 connector to the Telco-50 connector on the corresponding splitter card in the left column (labeled x-1) of the splitter chassis. Use a short Telco-50 cable to connect a line card's 25-48 Telco-50 connector to the Telco-50 connector on the corresponding splitter card in the right column (labeled x-2) of the splitter chassis. 36 IES-5000 Series User's Guide Chapter 2 Hardware Installation and Connections Figure 17 IES-5000 Front Panel Telco-50 Connections (with 6 Line Cards) IES-5000 Series User's Guide 37 Chapter 2 Hardware Installation and Connections Figure 18 IES-5005 Front Panel Telco-50 Connections (with 4 Line Cards) 2. 4. 2 72-port Line Card Connections When using 72-port line cards (such as the ALC1272G) use an IES-5000ST splitter card chassis in conjunction with an IES-5005ST splitter card chassis, as shown in the following figure. 38 IES-5000 Series User's Guide Chapter 2 Hardware Installation and Connections Figure 19 IES-5000 Front Panel Telco-50 Connections (with 72-port Line Cards) The 72-port line cards use long, medium and short Telco-50 cables (see Appendix A on page 73 for the exact lengths of each cable). IES-5000 Series User's Guide 39 Chapter 2 Hardware Installation and Connections These cables are different in length from the "long" and "short" cables used with the other line cards. See the appendix on product specifications for details. Use a long Telco-50 cable to connect a 72-port line card's 1~24 Telco-50 connector to the Telco-50 connector on the corresponding splitter card. Use a medium Telco-50 cable to connect a 72-port line card's 25~48 Telco-50 connector to the Telco-50 connector on the corresponding splitter card. Use a short Telco-50 cable to connect a 72-port line card's 49~72 Telco-50 connector to the Telco-50 connector on the corresponding splitter card. 2. 4. 2. 1 72-port Line Card to Splitter Card Connections Connect the line card ports to the splitter or extension card ports as described in the following table, which represents the IES's front panel. In the numbers in this table, the first number refers to the line card's slot in the IES-5000 (1 to 8) and the numbers in parentheses refer to the Telco-50 port connector on the line card (ports 1~24, 25~48 and 49~72). Table 1 72-port Line Card Connections CHASSIS IES-5000 SLOT # 1 2 3 4 5 6 7 8 IES5000ST 1 2 3 4 5 6 7 8 IES5005ST 1 2 3 4 LINE CARD TELCO-50 CONNECTORS 1 (1~24) 2 (1~24) 3 (1~24) 4 (1~24) 5 (1~24) 6 (1~24) 7 (1~24) 8 (1~24) 1 (1~24) 2 (1~24) 2 (25~48) 3 (1~24) 4 (1~24) 4 (25~48) 5 (1~24) 6 (1~24) 6 (25~48) 7 (1~24) 8 (1~24) 8 (25~48) 1 (25~48) 2 (25~48) 3 (25~48) 4 (25~48) 5 (25~48) 6 (25~48) 7 (25~48) 8 (25~48) 1 (49~72) 2 (49~72) 3 (49~72) 4 (49~72) 5 (49~72) 6 (49~72) 7 (49~72) 8 (49~72) 1 (25~48) 1 (49~72) 2 (49~72) 3 (25~48) 3 (49~72) 4 (49~72) 5 (25~48) 5 (49~72) 6 (49~72) 7 (25~48) 7 (49~72) 8 (49~72) SPLITTER CARD TELCO-50 CONNECTORS 40 IES-5000 Series User's Guide Chapter 2 Hardware Installation and Connections 2. 4. 3 VoIP Line Card Telco-50 Connections When you use a VoIP line card in conjunction with an ADSL or VDSL card, place the VoIP card and its extension cards in the chassis directly adjacent to the DSL card and its splitter cards, as shown in the following figure (this example uses the ALC line card and ASC1024 splitter). Figure 20 DSL and VoIP Front Panel Telco-50 Connections (2 Splitter Chassis) ALC1248G ASC1024 SEC1024 Use a Telco-50 cable to connect the SEC1024's USER Telco-50 connector on the rear of the splitter chassis to the CO Telco-50 connector on the rear of an ADSL or VDSL splitter card. Alternatively, use a Telco-50 cable to connect the SEC1024s USER Telco-50 connector directly to the Main Distribution Frame when no ADSL/VDSL service is required (see Section 2. 4. 5 on page 41). 2. 4. 4 Splitter Chassis Rear Panel Connections (DSL) A DSL splitter card separates the voice signal from the DSL signal. It feeds the DSL signals to the DSL line card and diverts the voice signal to the CO Telco-50 connector (or wire wrapping pins) on the splitter chassis' rear. Connect the CO Telco-50 connectors to the PBX or PSTN/ISDN switch when using the ADSL splitter card. Connect the USER Telco-50 connectors to the subscribers' telephone wiring. In most multitenant unit applications, the USER pins connect to the subscribers' telephone wiring via Main Distribution Frame (MDF). See Section 2. 5. 4 on page 43 for example splitter chassis rear panel connections. 2. 4. 5 Splitter Chassis Rear Panel Connections (VoIP) When using the VoIP line card in conjunction with an ADSL or VDSL card and its associated splitter card(s), connect the VoIP line card's extension card(s) and the DSL splitter card(s) as follows. IES-5000 Series User's Guide 41 Chapter 2 Hardware Installation and Connections Figure 21 DSL and VoIP Rear Panel Telco-50 Connections (2 Splitter Chassis) ASC1024 SEC1024 · Connect the USER Telco-50 connector from the extension card attached to the VoIP line card's 1 ~ 24 ports to the CO Telco-50 connector of the splitter card attached to the DSL line card's 1 ~ 24 ports. [. . . ] In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A Warning: Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASS 1 PRODUCT COMPLIES WITH 21 CFR 1040. 10 AND 1040. 11. [. . . ]