User manual ZYXEL IES-1248-51A

[. . . ] ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. ii Copyright IES-1248-51A Hardware Installation Guide ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. [. . . ] Connect the mini-RJ-11 end of the console cable to the console port of the network module. After the initial setup, you can modify the configuration remotely through Telnet connections. Hardware Connections 4-1 IES-1248-51A Hardware Installation Guide Figure 4-2 Console Port Connection 4. 3 · · SHDSL Port Connections For detailed specifications about the associated RJ-11 connector, refer to the Pin Assignment appendix. For more detail about MDF connections refer to the Notes About MDFs (Main Distribution Frames) shown later in this section. The SHDSL ports connect to an MDF (Main Distribution Frame) and end-user equipment via telephone wire. The procedure shown next explains how to complete a single G. SHDSL connection (SAM1008) to an MDF via an SHDSL port. Instructions on ADSL connections (AAM1008) come later. 4. 3. 1 Step 1. Step 2. Procedure to Complete a G. SHDSL Connection Connect the RJ-11 end of a telephone wire to the SHDSL port on the front panel of the SAM1008 as shown next. Connect the other end of the telephone wire to the upper port of an MDF (Main Distribution Frame) using a punch-down tool. 4-2 Hardware Connections IES-1248-51A Hardware Installation Guide Figure 4-3 SHDSL Port and MDF Connections Step 3. Step 4. Connect a different telephone wire to the lower port of the MDF using a punch-down tool. Connect the other (RJ-11) end of the telephone wire to the end-user G. SHDSL modem/router. When you finish this procedure your connections should look similar to the figure shown next. Connections between the user's computer and modem/router are not described here. Hardware Connections 4-3 IES-1248-51A Hardware Installation Guide Figure 4-4 SHDSL Port, MDF and User Equipment Connections Notes About MDFs (Main Distribution Frames) An MDF is usually installed between end-users' equipment and the telephone company (CO) in a basement or telephone room. The MDF is the point of termination for the outside telephone company lines coming into a building and the telephone lines in the building. 4-4 Hardware Connections IES-1248-51A Hardware Installation Guide Figure 4-5 Magnified View of MDF Wiring Connect wiring from end-user equipment to the lower ports of an MDF using a telephone wire. Connect wiring from the telephone company to the upper ports of an MDF (see the previous figure). Users A and B have telephone (only) service. Figure 4-10 Two Separate MDFs for End-user and CO Connections Please refer to the following figure for the ADSL connection schema. User B now has ADSL service also (see the following figure). 4-10 Hardware Connections IES-1248-51A Hardware Installation Guide Figure 4-11 Installation Scenario C Procedure To Connect To MDFs Step 1. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008. Connect the other ends of the telephone wires to the upper ports of MDF 3 using a punch-down tool. Connect the lower ports of MDF 3 to the upper ports of MDF 2 for those users that want ADSL service. (Users who want telephone service only, retain the original connection from the top port of MDF 2 to the bottom port of MDF 1. ) Connect the telephone wiring from the end-user's ADSL equipment to the lower ports of MDF 2. Connect the RJ-11 connector ends of telephone wires you want for voice service to the AAM1008's CO ports. Connect the other ends of the telephone wires to the lower ports of MDF 4 using a punch-down tool. Connect the top ports of MDF 4 to the bottom ports of MDF 1 using regular telephone wires. Step 8. Hardware Connections IES-1248-51A Hardware Installation Guide Connect the top ports of MDF 1 to the telephone company. 4. 4. 5 LAN Port (Ethernet) Connection Connect the LAN port of your SAM1008 to an Ethernet WAN switch using a straight-through Category 5 UTP (Unshielded Twisted Pair) cable with RJ-45 connectors. You may stack multiple IES-1248-51A units up to the number of ports available on the Ethernet switch as shown next. Figure 4-12 Stacking Multiple IES-1248-51A Units 4. 4. 6 Power Cord Connect the female end of the power cord to the power receptacle on the front panel of your IES-1248-51A (to the right of the fuse housing) as shown next. [. . . ] 4-1 Console Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1, A, B, C Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A Fuse Rated. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G G G. SHDSL modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2, 6-3 G. SHDSL Modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]