User manual ZYXEL ES-315-F QUICK GUIDE V3.70

[. . . ] · Avoid getting dust and other contaminants into the optical bores. 3 ES-315-F Quick Start Guide · SFP transceivers are equipped with a Class 1 laser, which emits invisible radiation when the device or system is powered up. To avoid possible eye injury, do not look into an operating fiber-optic transceiver's connectors. · Do not remove and install an SFP transceiver more often than is absolutely necessary. 1 Disconnect all fiber-optic cables from an SFP transceiver before installing or removing it. [. . . ] Make sure the device to which the corresponding port is connected is turned on and working normally. If this does not help, turn the ES-315-F off and on again. 2. 4 Set Up Your Computer's IP Address This section shows you how to set up your computer to access the ES-315-F. 11 ES-315-F Quick Start Guide You must set your computer to use a static IP address in the 192. 168. 1. 2 - 192. 168. 1. 254 range with a subnet mask of 255. 255. 255. 0. The following instructions are for the Windows 2000, Windows NT and Windows XP operating systems. 4 Select Internet Protocol (TCP/IP) (under the General tab in Windows XP) and click Properties. 5 The Internet Protocol TCP/IP Properties screen opens (the General tab in Windows XP). 12 ES-315-F Quick Start Guide Note down your computer's current IP settings before you change them. You may need them later. 6 Select Use the following IP address and fill in the IP address (choose one in the range 192. 168. 1. 2 192. 168. 1. 254), Subnet mask (255. 255. 255. 0), and Default gateway (192. 168. 1. 1) fields. 8 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 13 ES-315-F Quick Start Guide Close the Network Connections window. 3 Log In To the Web Configurator Take the following steps to access the ES-315-F for initial configuration. Use Internet Explorer 6. 0 and later versions or Netscape Navigator 7. 0 and later versions with JavaScript enabled and pop-up blocking disabled. Open an Internet browser (such as Internet Explorer or Netscape Navigator). Enter the ES-315-F's IP address in the address bar. The ES-315-F's default IP address is 192. 168. 1. 1. 14 ES-315-F Quick Start Guide A window similar to the following appears. Enter the default username (admin) and the default password (1234). Click OK. If you do not see this screen, make sure that your Internet browser allows pop-up windows (in Internet Explorer, select Tools > Pop-up Blocker and then select Turn Off Pop-up Blocker). If this does not help, make sure the IP addresses and subnet masks of the ES-315-F and the computer are in the same IP address range (see section 2. 4). 15 ES-315-F Quick Start Guide The Status screen displays. 4 Set the Password For security reasons, you should change the password when you first log in. Take the following steps to do this. 16 ES-315-F Quick Start Guide 1 Click Management in the navigation panel on the left of the screen. Then, click Logins. 2 The following screen displays. 3 Enter the login information you want to use, as follows. The password is case sensitive - "ABCD" is not the same as "abcd". 17 ES-315-F Quick Start Guide · Enter the default password (1234) in the Old Password field. · Choose a new password up to 31 characters in length (letters, numerals, spaces, dashes (-) and underscores (_) are allowed) and enter it in the New Password field. An asterisk (*) displays for each character you enter. Be sure to record the new password and keep it in a safe place. If you forget this information, you will need to reset the ES-315-F to its factory defaults (press the Reset button in for 3 ~ 5 seconds). · Re-enter the new password in the Re-type to confirm field. · Log in to the web configurator again, using your new password. · Click Save. 5 Set Up Your Network This section shows how to set the ES-315-F's IP address so it is in the same subnet as the other devices on your network. If it is not in the same subnet, it cannot communicate with the other devices. 18 ES-315-F Quick Start Guide In the web configurator's navigation panel, click Basic Settings, then select IP Setup. The following screen displays. 19 ES-315-F Quick Start Guide If you change the ES-315-F's IP address, you will need to use the new one in order to access the web configurator once you click OK. · If you have a DHCP server on your network that can assign a dynamic IP address to your ES-315-F, go to section 5. 1. [. . . ] · Return your computer's IP settings to their previous values, if necessary. 21 ES-315-F Quick Start Guide If you cannot access the ES-315-F, have problems accessing the Internet through the ES-315-F, or forget the password, you may need to reset the ES-315-F to its factory defaults. To restart the ES-315-F, hold the RESET button on the rear panel in for three to five seconds. 6 Wall-mount the ES-315-F Take the following steps to hang your ES-315-F on a wall. 2 Drill two holes for the screws, exactly 104 mm apart. Be careful to avoid damaging pipes or cables located inside the wall when drilling holes for the screws. 22 ES-315-F Quick Start Guide 3 Do not insert the screws all the way into the wall. Leave a small gap of about 0. 5 cm between the heads of the screws and the wall. [. . . ]