User manual ZYXEL ES-3024 BROCHURE

[. . . ] Dimension ES-3024 Ethernet Switch December 2003 Version 3. 50 User's Guide Dimension ES-3024 Ethernet Switch Copyright Copyright © 2003 by ZyXEL Communications Corporation The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patents rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. [. . . ] If it does not form a VLAN with a particular port then the switch cannot be managed from that port. These are the egress ports; an egress port is an outgoing port, that is, a port through which a data packet leaves. If you wish to allow two subscriber ports to talk to each other, you must define the egress port for both ports. If it does not form a VLAN with a particular port then the switch cannot be managed from that port. Click Apply to save the changes, including the "wizard settings". Click Cancel to start configuring the screen again. Outgoing Apply Cancel VLAN 7-13 Dimension ES-3024 Ethernet Switch Chapter 8 Static MAC Forward Setup Use these screens to configure static MAC address forwarding. 8. 1 Introduction to Static MAC Forward Setup A static MAC address entry is an address that has been manually entered in the MAC address learning table. When you set up static MAC address rules, you are setting static MAC addresses for a port. Devices that match static MAC address rules on a port can only receive traffic on that port and cannot receive traffic on other ports. This may reduce unicast flooding. 8. 2 Configuring Static MAC Forwarding Click Static MAC Forwarding to display the configuration screen as shown. Figure 8-1 Static MAC Forwarding The following table describes the labels in this screen. Table 8-1 Static MAC Forwarding LABEL Active Name DESCRIPTION Select this check box to activate your rule. You may temporarily deactivate a rule without deleting it by clearing this check box. Enter a descriptive name for identification purposes for this static MAC address forwarding rule. Static MAC Forward Setup 8-1 Dimension ES-3024 Ethernet Switch Table 8-1 Static MAC Forwarding LABEL MAC Address VID Port Add Cancel Clear DESCRIPTION Enter the MAC address in valid MAC address format, that is, six hexadecimal character pairs. Select a port where the MAC address entered in the previous field will be automatically forwarded. Click Clear to clear the fields to the factory defaults. 8. 3 Viewing and Editing Static MAC Forwarding Rules To view a summary of the rule configuration, scroll down to the summary table at the bottom of the Static MAC Forwarding screen. To change the settings of a rule, click a number in the Index field. Figure 8-2 Static MAC Forwarding: Summary Table The following table describes the labels in this screen. Table 8-2 Static MAC Forwarding: Summary Table LABEL Index Active Name MAC Address Port Delete Cancel DESCRIPTION Click an index number to modify a static MAC address rule for a port. This field displays whether this static MAC address forwarding rule is active (Yes) or not (No). This field displays the descriptive name for identification purposes for this static MAC addressforwarding rule. This field displays the MAC address that will be forwarded and the VLAN identification number to which the MAC address belongs. This field displays the port where the MAC address shown in the next field will be forwarded. Check the rule(s) that you want to remove in the Delete column, then click the Delete button. Click Cancel to clear the selected checkboxes in the Delete column. 8-2 Static MAC Forward Setup Dimension ES-3024 Ethernet Switch Chapter 9 Filtering This chapter discusses static IP and MAC address port filtering. 9. 1 Introduction to Filtering Port filtering means sifting traffic from one or all ports to one or all ports based on the source and/or destination MAC addresses and VLAN group (ID). 9. 1. 1 · · · · · Note About Configuration The following rules apply when configuring filtering. [. . . ] The switch also does not forward frames to "forbidden" ports. If after looking at the SVLAN, the switch does not have any ports to which it will send the frame, it won't check the port filter. 27. 4. 12 Syntax: vlan1q svlan delentry sys sw vlan1q svlan delentry <VID> where <VID> = The VLAN ID [1 ­ 4094]. This command deletes the specified VLAN ID entry from the static VLAN table The following example deletes entry 2 in the static VLAN table. ES-3024> sys sw vlan1q svlan delentry 2 Figure 27-13 vlan1q svlan delentry Command Example 27. 5 vlan1q svlan active Syntax: sys sw vlan1q svlan active <VID> This command enables the specified VLAN ID in the SVLAN (Static VLAN) table. 27. 6 vlan1q svlan inactive Syntax: sys sw vlan1q svlan inactive <VID> This command disables the specified VLAN ID in the SVLAN (Static VLAN) table. 27. 7 vlan1q svlan list Syntax: sys sw vlan1q svlan list This command shows the IEEE 802. 1Q Tagged SVLAN (Static VLAN) table. 27-8 IEEE 802. 1Q Tagged VLAN Dimension ES-3024 Ethernet Switch An example is shown next. [. . . ]