User manual ZYXEL B-5000 QUICK START GUIDE

[. . . ] The excellent RF performance means that the users do not need to be inside the same building or even in the same block. The ZyAIR can also function as a bridge or router to provide a wireless backbone connection between two or more buildings. Rugged die-cast, watertight construction, built-in lightening protection, and grounding make the ZyAIR perfect for outdoors applications. The embedded web-based configurator includes a wireless link test that helps you to align the device. [. . . ] Position the antenna vertically for the best omni-directional signal reception. 8 ZyAIR B-5000 Quick Installation Guide Figure 9 - Installation Layout Step 2. Attach the MIL-C-5015 style (RS-232) console cable to the serial port adapter. Connect the other cable end (DB9 female) to a terminal or a PC running a terminal emulation program. Connect the female end of the power cord to the inline power injector, and then connect the male end of the power cord into a power outlet or power strip. The POWER LED on the front of the Inline power injector should turn on. Run the Ethernet cable (included in your package) from DATA IN port (on the front panel of the inline power injector) to the Ethernet port on a computer. Connect the MIL-C-5015 style Ethernet connector to the special Ethernet port on the bottom of the ZyAIR. Connect the RJ-45 Ethernet connector (the other end of the special Ethernet cable) into the POWER & DATA OUT port on the front of the inline power injector. Step 4. Step 6. When the ZyAIR receives power over the Ethernet cable, the ZyAIR will start its boot sequence and the ACTIVE LED on the front of the Inline power injector will turn on. You can configure the ZyAIR using the HTML browser, such as Internet Explorer or Netscape Navigator from a remote host or PC. See Part I of your ZyAIR User's Guide for a quick setup guide. 9 ZyAIR B-5000 Quick Installation Guide 4 Hardware Installation In general, the best location for the access point is at the center of your intended wireless coverage area. It is recommended that you do the initial configuration of the ZyAIR prior to mounting. The Outdoor Access Point & Bridge device can be mounted on the side of a building or mounted to an antenna mast as described: A wall (side) mount allows for mounting an antenna (mast) on the side of a building or on the side of an elevated penthouse. This will provide a convenient mounting location when the roof overhang is not excessive and/or the location is high enough to provide a clear line of sight. A transmitter within a wireless device sends an RF signal to the antenna, which propagates the signal through the air. The antenna also operates in reverse by capturing RF signals from the air. Choosing the right antennas and positioning them properly increases the range and coverage area of a wireless LAN. In most situations mounting an antenna directly to the wall will not allow you to properly align the antenna with the corresponding antenna at the opposite end of your wireless link. As poor alignment will typically result in poor performance, we advise you to always mount the Outdoor Access Point & Bridge to a mast. 4. 1 Antenna Mast/Antenna Requirements To accommodate the ZyAIR, the mast must satisfy the following requirements: The construction of the mast must be of a sturdy, weatherproof and non-corrosive material, for example, galvanized or stainless steel construction pipe. Typical diameter of the mast should be between 35 mm (1. 4") and 41 mm (1. 625"). Subject to the type of mast that you intend to install, other diameters are possible. The height of the antenna mast must be sufficient to allow the antenna to be installed at least 1. 5 m (5') above the peak of the roof. [. . . ] Therefore alignment of this type of antennas is less critical than for directional antennas. For omni-directional antennas mounted on a table, desk, and so on, point the antenna up. For omnidirectional antennas mounted on a wall or ceiling, point the antenna down. For a single AP application, place omni-directional antennas as close to the center of the coverage area as possible. [. . . ]