User manual ZOTAC ZBOX NANO ID63 PLUS

[. . . ] · USB: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. (Center / Subwoofer): Connects to the center and subwoofer channel in the 7. 1 channel audio system. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 7. 1 channel audio system. (Surround Left / Surround Right): Connects to the surround left and surround right channel in the 7. 1 channel audio system. [. . . ] The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. The FDD connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDD on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both the FDD port and the floppy connector. 2. 5. 2 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by SATA cable. 2. 5. 3 PCI and PCI Express slots Install PCI Express X1 graphics card into slot "PCIE1". Install PCI card into slots "PCI1" or "PCI2" . - 10 - XFX Motherboard Series User Guide Chapter 3 Jumpers & Headers Setup 3. 1 Checking Jumper Settings · For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position. · For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in. How to identify the PIN1 jumpers?Please check the motherboard carefully, the PIN1 is marked by "1" or white thick line. 3. 2 CMOS Memory Clearing Header The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d) whenever there is modification on the CPU or memory modules. This header uses a jumper cap to clear the CMOS memory and have it reconfigured to the default values stored in BIOS. JBIOSSLC · The button of CMOS_BT1 NC Dual_BIOS on back panel, if press this 1-2 Standard BIOS button on any environment, 2-3 Overclock BIOS the function is same with Pins 2 and 3 be shorted. · When the boot is from standard BIOS, the LEDA1 LED on board will light on; if the boot is from Overclock BIOS, the LEDB1 LED on board will light on. Set the jumper cap back to its default settings --- pin 1 and pin 2 shorted. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS setup menu right after powering on system. IDE Configuration Click <Press Enter> key to enter its submenu, it will be display IDE configuration, also you can set the ATA/IDE, SATA function from the options and set the IDE boot order, or set it as IDE Master, Slave within them. Floppy Configuration Click <Press Enter> key to enter its submenu, it will be display floppy configuration, and this item sets the type of floppy drives installed. - 17 - XFX Motherboard Series 4. 5. 2 Control Keys User Guide Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. Please check the following table for the function description of each control key. Control Key(s) / / +/ -/PU/PD <Enter> <ESC> <F1> <F2/F3> <F5> <F7> <F8> <F9> <F10> Function Description Move cursor left or right to select Screens Move cursor up or down to select items To Change option for the selected items To bring up the selected screen Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu General help Change Colors Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Discard Changes Load Failsafe Defaults Load Optimal Defaults Save configuration changes and exit setup - 18 - XFX Motherboard Series 4. 5. 3 Advanced Setting Main Advanced Boot BIOS SETUP UTILITY Security Power JUSTwOOT!Exit User Guide Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction. CPU Con guration Chipset Onboard Devices PCIPnP Con gure CPU. Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. This submenu including these configurations, such as CPU, Northbridge, Southbridge, Onboard Device, only CPU Configuration submenu dispay diallog box as follwoing. BIOS SETUP UTILITY Advanced CPU Con guration Moudule Version:13. 24 AGESA Version:3. 1. 7. 0 Physical Count:1 Logical Count:2 AMD Sempron(tm)Processor LE-1100 Revision :G2 Cache L1 :128 KB Cache L2 :256 KB Cache L3 :N/A Speed :1912MHz, NB Clk : N/A Current FSB Multiplier:9. 5x Maximum FSB Multiplier:9. 5x Able to Change Freq. :Yes uCode Patch Level :None Required Garp Error Reporting [Disabled] Microcode Update Secure Virtual Machine Mode Cool 'n'Quiet [Enabled] [Enabled] [Disabled] This option should remain disabled for the normal operation. The Driver developer may enable it for testing purpose. +F1 F10 ESC Select Screen Select Item Change Field General Help Save and Exit Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. CPU Configuration Click <Press Enter> key to enter its submenu, it will be display configureted CPU information, including Module Version, Manufacturer , CPU type, Frequency, FSB Speed, Cache L1 , Cache L2 and so on. - 19 - XFX Motherboard Series User Guide Chipset Click <Press Enter> key to enter its submenu, that can select primary graphics adapter from optional items, or set Internal VGA or External VGA CARD to display. BIOS SETUP UTILITY Advanced Advanced Chipset Settings Primary Graphics Adapter [PCIE VGA Card Firs] iGPU and Ext-VGA Selection [Both Exist and iGPU] iGPU Frame Bu er Detect [Disabled] iGPU Frame Bu er Size [256MB] PCI VGA Card First Internal VGA First PCIE VGA Card First Select Screen Select Item +- Change Field F1 General Help F10 Save and Exit ESC Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. [. . . ] Exit Over Voltage and Clock Setting Frequency/Voltage Control LAN1 BootROM Control Memory Con guration CPU Voltage Control DRAM Voltage Control Chipset Voltage Control Memory 2T Mode CPU/LDT Spread Spectrum PCIE Spread Spectrum SATA Spread Spectrum iGPU Spread Spectrum [Disabled] [Auto] [Auto] [Auto] [2T Mode] [Disabled] [Disabled] [Disabled] [Disabled] To Enable/Disable Onboard PCIE LAN BootR Hyper Transport Con guration CPU Frequency, MHz [200] Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02. 61 (C)Copyright 1985-2006, American Megatrends, Inc. These options allow you to manage LAN BootRom Contor, CPU Voltage Control, Dram Voltage, Chipset Voltage Contorl, Memory Mode, and so on. And the option of CPU Frequency, MHz allows you overclock CPU clock, the Min is 200MHz, the Max is 400, per keyin "+"/"-" to select clock. - 23 - XFX Motherboard Series 4. 5. 8 Exit Options Save Changes and Exit User Guide Highlight this item and select <Ok>, then press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Exit system setup after saving the changes. [. . . ]