User manual ZOTAC ZBOX NANO ID61 PLUS

[. . . ] , If you use an extension cord, please use the UL listed cord and make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating. Care during use ™™ Do not walk on the power cord or allow anything to rest on it. ™™ When the system is turned off, a small amount of electrical current still flows. Always unplug all power, modem, and network cables from the power outlets before cleaning the system. [. . . ] Use the ports for USB 3. 0 devices for maximum performance with USB 3. 0 compatible devices. Ethernet port The eight-pin RJ-45 LAN port supports standard Ethernet cable for connection to a local area network (LAN) with speeds of 10/100/1000Mbps. USB 2. 0 ports The USB (Universal Serial Bus) ports are compatible with USB devices such as keyboards, mice, cameras and hard disk drives. eSATA port The external SATA port is compatible with e. SATA devices such as external hard drives and Blu-ray drives. WiFi antenna connector The WiFi antenna connector supports WiFi antenna module. Ventilation area The ventilation area is designed for cooling. 7 ZOTAC ZBOX nano BIOS settings of specific functions ZOTAC ZBOX nano has some specific functions which can be enabled or disabled in BIOS settings, such as LED indicator, and USB2. 0 charge. How to disable the ring LED indicator 1. Turn on the ZBOX nano mini-PC, then press <Delete> to enter the BIOS SETUP UTILITY. 2. Use the arrow keys to navigate to the Chipset menu and select Onboard Device Configuraion. 8 ZOTAC ZBOX nano 3. Press <Enter> to display the Onboard Device Configuration and navigate to Back Light. 4. Press <Enter> and select Disabled. 5. Press F10 to save the configuration and exit. The PC will reboot. 9 ZOTAC ZBOX nano How to enable USB2. 0 charge (for S3/S4/S5 status) 1. In Chipset menu, select Onboard Device Configuration and press <Enter>. 2. Use the arrow keys to enter the item USB 2. 0 Mode, and select Charge Mode. Note: Before charging via USB2. 0 in S5 status, please make sure the Deep S5 is disabled. 1. In Advanced menu, select Wake Up Event Settings and press <Enter>. 10 ZOTAC ZBOX nano 2. Use the arrow keys to enter the item Deep S5, and select Disabled. High Current/Fast Charging USB ports If you want a faster, less restricted way of charging your mobile phone and tablet from all USB2. 0 ports, simply install the USB Charging driver (for Windows7) which allows you to charge a USB devices quickly and even supports continuous charging when your mini-PC enters Standby mode (S1), Suspend to RAM (S3), Hibernation mode (S4) or Power off mode (S5). With this USB Charging driver installed, you can enjoy marvelous charging experience than ever. Please visit the ZOTAC website “Support” -> “Download” to get the USB Charging driver for your mini-PC: http://www. zotac. com 11 ZOTAC ZBOX nano Customizing the ZOTAC ZBOX nano Please follow the instructions below to remove the cover of the ZOTAC ZBOX nano before customizing. Gently remove the cover from the side marked with words: Pull upward. 12 ZOTAC ZBOX nano Installing a memory module 1. Locate the SO-DIMM memory slot and insert a SO-DIMM memory module into the slot at a 45 degree angle. 2. To ensure proper operation and reliability, leave aproximately 4 inches (10 cm) of spacing in front of the ventilation holes. • ZOTAC ZBOX nano mini-PC systems provide ample expansion in a miniature form factor, please use connectors and cables that are appropriate in size to avoid interference. Mounting the ZOTAC ZBOX nano to a LCD monitor The ZOTAC ZBOX nano is monitor-mountable using the included VESA mount. 1. Secure the VESA mount to the LCD monitor using screws (not included). Disclaimer: ZOTAC cannot be held liable for damages resulting from an improper installation. 2. Align the ZOTAC ZBOX mounting holes to the VESA mount attachment pegs. Attach the ZOTAC ZBOX to the VESA mount and gently press down to secure the ZBOX to the mount. 18 ZOTAC ZBOX nano 3. Connect the ZOTAC ZBOX nano to your LCD monitor with an HDMI/DP cable. IR receiver Users can control the LCD monitor/TV by either IR receiver or external USB IR receiver. [. . . ] 3. Highlight “Internet Protocol (TCP/IP)” and click “Properties”. 7. After entering all of the related values, click “OK” to finish the configuration. 23 ZOTAC ZBOX nano Using a dynamic IP (PPPoE connection) 1. 2. 3. 4. 5. 6. Repeat Step 1-3 in the previous section. Select “Obtain an IP address automatically” and click “OK”. [. . . ]