User manual ZOTAC ZBOX ID-85 PLUS

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - - - - REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. While every precaution has been taken in the preparation of this manual, no responsibility for errors or omissions is assumed. [. . . ] These connectors support the thin Serial ATA cables for primary storage devices. The motherboard incorporates two SATA II ports with maximum transfer rate up to 3. 0 Gb/s each. SATA-Pin Definition Pin 1 2 3 4 5 6 7 Signal GND TXP TXN GND RXN RXP GND 19 Intel D2550-ITX series Motherboard Expansion Slots The motherboard contains three expansion slots, twe Mini PCIe slots and one PCIe x16 slot. 1. 5V J1 J2 PCIE2 Mini PCI Express Slots-J1/J2 There are two Mini PCI Express slots. (Please refer to page 13 to install the mSATA SSD module. ) PCI Express x16 Slot-PCIE_X16 There is one PCIe x16 slot reserved for graphics card. It is fully compliant with PCIE 2. 0 specification. 20 1. 5V Hardware Installation Jumper Settings This section explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. CMOS Clear Jumper-JP1 JP1 1 1 Selection Normal* CMOS Clear Open * = Default setting. 1-2* 2-3 Close If you want to clear the system configuration, use the JP1 (Clear CMOS Jumper) or SW1 (Clear CMOS Button) to clear data. If the CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. 21 Intel D2550-ITX series Motherboard Configuring the BIOS Enter BIOS Setup This section discusses how to change the system settings through the BIOS Setup menus. Correctly setting the BIOS parameters is critical to maintain optimal system performance. 2. Press the Del key when the following message briefly displays at the bottom of the screen during the Power On Self Test (POST). We reserve the right to update the BIOS version presented in the manual. q EHCI Hand-Off Allows you to enable support for operating systems without an EHCI hand-off feature. q Device power-up delay Allows you to set device power-up delay. 25 Intel D2550-ITX series Motherboard Intel Fast Flash Standby The items in this menu allow you to change Intel Fast Flash standby features. Press <enter> to display the configuration options: q iFFS Support Use this item to enable or disable iFFS. q Entry on S3 RTC Wake Use this item to enable or disable entry on S3 RTC wake. q Entry After Use this item to set the number of minutes of entry after. q Entry on S3 Critical Battery Wake Use this item to enable or disable entry on S3 critical battery wake. PC Health Menu Select PC Health from the BIOS Setup Utility menu to display the system menu. q CPU Fan Control Mode Use this item to select CPU FAN Control mode. q Highest Fan Duty Use this item to select the highest fan dutycycle. 26 Power Management Menu The items in this menu allow you to control the system power management. Press <Enter> to display the configuration options: q Enable Hibernation Enable or disable system ability to hibernation (OS/S4 Sleep State). q ACPI Sleep State Select the highest ACPI sleep state, the system will enter when the SUSPEND button is pressed. q Restore AC Power Loss This item allows you to configure how the system board responds to a power failure. q DeepSleep (Erp Compliant) When enabled, wake up from S4/S5 can only be done by power button. [. . . ] - If you are not sure how to upgrade the BIOS, please take your computer to an Authorized Service Center and have a trained technician do the work for you. 31 Intel D2550-ITX series Motherboard Installing Drivers and Software Note: 1. It is important to remember that before installing the driver disk that is shipped in the kit, you need to load your operating system. For best compatibility, please only use the onboard SATA, eSATA or USB 2. 0 ports as the OS installation source drive connection. The kit comes with a driver disk that contains utility drivers and additional software. [. . . ]