User manual ZOTAC ZBOX ID-42 PLUS

[. . . ] If you use an extension cord, please use the UL listed cord and make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating.  Care during use ™™ Do not walk on the power cord or allow anything to rest on it. ™™ When the system is turned off, a small amount of electrical current still flows. Always unplug all power, modem, and network cables from the power outlets before cleaning the system. [. . . ] Bluetooth antenna connector The bluetooth antenna connector supports bluetooth antenna module. Power input (DC19V) The supplied power adapter converts AC power to DC power for use with this jack. To prevent damage to the PC, always use the supplied power adapter.  The power adapter may become warm to hot when in use. Do not cover the adapter and keep it away from your body. 7 ZOTAC ZBOX BIOS settings of specific functions ZOTAC ZBOX has some specific functions which can be enabled or disabled in BIOS settings, such as LED indicator, USB2. 0 charge and CIR controller. How to disable the ring LED indicator 1. Turn on the ZBOX mini-PC, then press <Delete> to enter the BIOS SETUP UTILITY. 2. Use the arrow keys to navigate to the PowerManage menu and select LOGO Indicator. 8 ZOTAC ZBOX 3. Press <Enter> and select Disabled. 4. Press F10 to save the configuration and exit. How to enable USB2. 0 charge (for S3/S4/S5 status) 1. In PowerManage menu, select USB2. 0 S3/S4/S5 Charge Function and press <Enter>. 9 ZOTAC ZBOX 2. Use the arrow keys to enter the item Rear / Front / Top USB2. 0 S3/S4/S5 Charge, and select Enabled. 3. Press F10 to save the configuration and exit. Note: Before charging via USB2. 0 in S5 status, please make sure the Deep S5 (DeepSleep(ErP Compliant) S5 in PowerManage menu) is disabled. 10 ZOTAC ZBOX How to disable CIR controller (for internal IR receiver) 1. Use the arrow keys to navigate to Advanced > OnBoard Device Control > CIR Controller Configuration. 2. Enter CIR Controller and select Disabled. Enabled: enable the internal IR receiver (default) Disabled: disable the internal IR receiver 3. Press F10 to save the configuration and exit. 11 ZOTAC ZBOX Installing Hardware inside ZOTAC ZBOX Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX. Gently remove the cover as the image below. 12 ZOTAC ZBOX Installing a memory module 1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot at a 45 degree angle. Note: When installing two SO-DIMM memory modules, please insert a module into the lower slot first. 2. Gently press down on the memory module until it locks into place by the arms of the memory slot. Note: This ZOTAC ZBOX accomodates two DDR3 SO-DIMM memory modules. You must install at least one module in one of the two slots. 13 ZOTAC ZBOX Removing the memory module 1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory module outwards, as shown in the image below, to release the memory module. 2. Remove the memory module from the slot at a 45-degree angle. 14 ZOTAC ZBOX Installing a hard disk 1. 2. Align the stand screw to the PC screw hole and then secure the Stand to the PC with a coin.  Installing your ZOTAC ZBOX to a monitor You can also install your ZOTAC ZBOX to the back of a monitor. To do so: 1. Secure the VESA mount to your monitor with four screws (HNM/M4x8). 2. Place your ZOTAC ZBOX on the VESA mount noting the correct alignment and then secure the PC to the VESA mount with a coin. [. . . ] Restart the system. Using your ZOTAC ZBOX Configuring wireless connection To connect to a wireless network, follow the instructions below: 1. Double-click the crossed wireless network icon (pic) on the notification area. 2. Select the wireless network you want to connect to from the list and click Connect. 3. After connection was established, you will see Connected.  For security concerns, Do NOT connect to an unsecured network, otherwise, the transmitted information without encryption might be visible to others. [. . . ]