User manual ZOTAC NM70ITX-C-E

[. . . ] WARNING! Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Press <enter> to display the configuration options: q Enable ACPI Auto Configuration Enable or disable ACPI Auto Configuration. q ACPI Sleep State Select the highest ACPI sleep state, the system will enter when the SUSPEND button is pressed. q Lock Legacy Resources Enable or diable Lock Legacy Resources. 18 Configuring the BIOS q S3 Video Repost This item allows you to enable or disable Repost Video on S3 Resume function. The default setting is [Disabled]. CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Press <enter>to display the configuration options: q EIST This item allows you to enable or disable Enhanced Intel SpeedStep Technology support. q CPU C3/C6/C7 Report This item allows you to enable or disable CPU C3/C6/C7 Report. SATA Configuration The items in this menu allow you to set or change the SATA configurations. Press <enter> to display the configuration options: q SATA Controller(s) Allows you to configure SATA controller. q SATA Mode Selection Allows you to choose SATA mode, including IDE Mode, AHCI Mode and RAID Mode. The items in this menu allow you to set or change the PCH-FW configurations. Press <enter> to display the configuration options: q Me FW Image Re-Flash This item allows you to enable or disable ME FW Image Re-Flash. PCH-FW Configuration USB Configuration The items in this menu allow you to change the USB-related features. Press <enter> To display the configuration options: q Legacy USB Support Allows you to enable or disable support for USB devices on legacy operating systems. q USB3. 0 Support Allows you to enable or disable support for USB3. 0 devices. q XHCI/EHCI Hand-Off Allows you to enable support for operating systems without an XHCI/EHCI handoff feature. q USB Mass Storage Driver Support Enable or disable USB Mass Storage Driver Support function q USB transfer time-out Allows you to set USB transfer time-out. 19 Intel NM70-ITX series Motherboard q Device reset time-out Allows you to set device reset time-out. q Device power-up delay Allows you to set device power-up delay. Super IO Configuration The items in this menu allow you to configure NCT5577D Super IO Chipset. q Serial Port 0/1 Configuration Allows you to set parameters of Serial Port 0/1 (C0MA). q Parallel Port Configuration Allows you to set parallel port (LPT/LPTE). Power Management Features The items in this menu allow you to control the system power management. Press <Enter> to display the configuration options: q Deep S5 When enabled, wake up from S5 can only be done by power button. q Restore AC Power Loss This item allows you to configure how the system board responds to a power failure. q Wake Up by USB KB/Mouse from S3 Enable or disable wake up by USB/PS2 KB/Mouse from S3. q Wake Up by PS2 KB/Mouse from S3/S4/S5 Enable or disable wake up by PS2 KB/Mouse from S3/S4/S5. q Wake Up by PCIE Device from S3/S4/S5 Enable or disable wake up by PCIE device from S3/S4/S5. Display Configuration The items in this menu allow you to set display Configuration. [. . . ] We reserve the right to update the driver version presented in the manual. The driver installation pictures shown in this section are for reference only. The kit comes with a driver disk that contains utility drivers and additional software. The driver disk that has been shipped with your motherboard contains the following software and drivers: q Intel Chipset Driver q HDA Sound Driver q Intel Graphics Driver q Ethernet PCI-E Driver q USB3. 0 Controller Driver q Intel Management Engine q Intel(R) Rapid Storage Technol Drivers Installation 1. [. . . ]