User manual ZIBRO PH733

[. . . ] P 720 - P 726 - P 729 - PH 733 2 6 5 3 FIN GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO MANUEL D'UTILISATION KYTTOHJE OPERATING MANUAL 4 22 40 56 72 88 4 2 ALLGEMEINE SICHERHEIT Aus Sicherheitsgrnden bitten wir Sie, die Bedienungsanleitung vor Inbetriebnahme sorgfltig zu lesen!Personen, die mit der Bedienungsanleitung nicht vertraut sind, drfen das Gert nicht bedienen. Nicht selbst reparieren. A 6 SIKKERHED GENERELT Ls denne brugsanvisning grundigt igennem af hensyn til sikkerheden!Personer, som ikke er fortrolige med brugsanvisningens indhold, m ikke anvende dette klimaanlg. [. . . ] Press the on/off button on the unit until you hear a beep (you will hear a beep after 8 seconds). The remote control is ready for use after the beep signal. 2 Press the C/F-button to set C (Celsius) or F (Fahrenheit). 3 The following functions can be selected with the mode button remote control. Automatic regulation of ventilator speed Cooling; Dehumidifying; Circulating; Heating (PH733). AUTOMATIC In the automatic mode , the device will cool, dehumidify or heat depending on the ambient temperature. When the temperature in the room changes, the mode changes automatically in order to maintain the desired temperature as accurately as possible. The colour of the transparent ring around the button on the front of the device will change depending on the mode. COOLING Cooling mode (blue) on the When the cooling mode is activated, the transparent ring around the button on the front of the device emits a BLUE light. 4 94 The following settings are possible in the cooling mode: The ventilator speed can be adjusted by pressing the Automatic regulation of ventilator speed High Average Low The temperature can be set between 18C and 32C (PH733: 16C - 32C) by pressing the and buttons. -button Whether the desired temperature can actually be reached depends on the ambient conditions. The room temperature remaining above the set temperature is normal. DEHUMIDIFICATION When the dehumidification mode is activated, the transparent ring around the button on the front of the device turns YELLOW. Dehumidifying mode (yellow) The dehumidification function can be used in different ways. 1) All models: Only connect the air exhaust hose to the air outlet and lead it outside, as when using the device in the cooling function with a single hose. The device will then dehumidify the air in the room and remove excess moisture through the air hose. 2) All models: Do not connect both the air supply and the air exhaust hose . Remove the rubber plug from the water drain and ensure that the water that is removed (e. g. 3) PH733: Connect the supplied water hose to the plug that fits into the water drain. into the water drain Lead the other end to a drain or sink and insert the plug . The maximum rise may be 1. 5 m from the floor on which the device is standing. During the dehumidification, the ventilator speed speed changes automatically to medium. The buttons are inactive. ATTENTION! In the automatic mode, the condensed moisture is always removed through the air exhaust hose . Removing the rubber plug from the water drain will allow the water to drain out at this point. The water drain can not be used. 4 95 When the device is not being used in the (manual) dehumidification mode, the plug must be removed from the water drain . CIRCULATING When the air circulation mode is switched on, the transparent ring around the button on the front of the device emits GREEN light. In this mode, the air is circulated and filtered but not cooled, dehumidified or heated. [. . . ] Windows or doors are open Close windows and/or or there are a large doors or place an extra number of people or heat airconditioner. Clean the filter or replace it (see chapter D). The device works insufficiently. Air inlet or exhaust is blocked. The device is standing on an uneven surface. Remove the blockage. Place the device on an even surface (less vibration). The compressor does not work. Wait 30 minutes until the temperature has dropped The overheating safety and then switch it on feature has been activated. batteries are empty. The remote control does not respond. Restore the connection The signal of the remote control cannot be received between the remote control and the air by the unit. [. . . ]