User manual ZENEC E GO

[. . . ] Copyright note The product and the information contained herein is subject to change without prior notification. This manual may not, in whole or in part, be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of ZENEC. Thank you for choosing ZENEC Navigation Software as your door-to-door in-car navigator. Read the Quick Start Guide first and start using ZENEC Navigation Software right away. [. . . ] On the following pages you will find the description of the different menu screens of ZENEC Navigation Software. From there you can access the following screens: Selecting the destination (for example an address or a POI) or using the search engine of ZENEC Navigation Software for any other reason (for example to look for the phone number of a POI). Managing the active route (obtaining information about it, changing or deleting it or parts of it) or planning a route without GPS reception. managing user data , such as saved locations (POIs , Favourites , Pins , and History items) , and Saved Routes. Managing the behaviour of ZENEC Navigation Software, for example the map layout during navigation, the used languages or the warnings. That is why maps in ZENEC Navigation Software look similar to paper road maps. However, ZENEC Navigation Software provides much more than regular paper maps: you can customise the look and the content of the map. During navigation, the screen shows route information and trip data (left screenshot), but when you tap the map, additional buttons and controls appear for a few seconds (right screenshot). Turn Preview, that is, the Opens the Route Information screen next route event Second event upcoming route Opens the Itinerary Current street and house n/a numbers on left and right Map view modes Switches between 2D and 3D map modes: 2D North-up 2D rotated 3D rotated Menu Repeat Voice Instruction Opens the Navigation menu Repeats the last voice guidance instruction with updated distance information. Cursor menu (appears when Opens the Cursor menu there is no GPS position or the Cursor is not at the current GPS position) Open/Close Map control buttons Tap this button to show or hide the following map control buttons: Zoom in/out Rotate left/right (3D map only) Tilt up/down (3D map only) Zoom preset buttons (2D map only) Tilt and zoom preset buttons (3D map only) Return to GPS position button Smart Zoom button Zoom in, zoom out , Return to GPS position (appears when GPS position is available and you have moved the map) Enable Smart Zoom (replaces the previous button if there is no GPS position or the map has not been moved) Zoom preset buttons Tap this button to move the map back to the current GPS position. If the map has been rotated in 3D mode, automatic map rotation is also reenabled. Tap one of the preset buttons to set the zoom level to a fix, predefined value. Tap&hold any of the buttons to set its value to the current zoom level, or to reset it to its original value. Tap&hold any of the buttons to set its value to the current tilt and zoom levels, or to reset it to its original value. ZENEC Navigation Software is connected to the GPS receiver, but the signal is too weak and the receiver cannot determine the GPS position. It indicates the following status information on a single strip: There are new, unread TMC events. A part of the route is mentioned in TMC events but could not be bypassed (for example, the destination is on a congested street). There are two fields reserved on the Map screen to display the next two manoeuvres (route events that are listed in the Itinerary). both the type of the event (turn , roundabout , exiting motorway , etc. Most of these icons are very intuitive and you also know them as road signs. The same symbols are used in both fields: The number of the exit is shown in the circle, but only for the next turn. In certain situations when route events are not important, these fields show other useful pieces of information. [. . . ] 6 to modify, extend, transform the Software Product (in whole or in part), to separate it into parts, combine it with other products, install it in other products, utilise it in other products, not even for the purpose of achieving interoperability with other devices; 7. 7 apart from using the computer program, to obtain information from the Database as a part of the Software Product, to decompile the Database, to use, copy, modify, extend, transform the Database in whole or in part or the group of data stored therein, or to install it in other products or otherwise, utilise it in other products or to transfer it, not even with the aim of achieving interoperability with other products. 2 The User may only use the contents available through the Software Product and provided by third parties and the data received through the services provided by third parties (including but not limited to the traffic data received from the RDS TMC traffic information service) for his/her own personal benefit and at his/her own risk. It is strictly prohibited to store, to transfer or to distribute these data or contents or to disclose them in full or in part to the public in any format or to download them from the product. [. . . ]