User manual ZEISS HBO 100

[. . . ] 9 Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Lamp Insertion and Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Start-Up of HBO 100 Microscope Illuminating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Focusing and Centering the HBO 100 Microscope Illuminator (423010) . . . . . . . . . . . . . . . 14 Focusing and Centering the HBO 100 Microscope Illuminator, self-adjusting (423011-9901) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The HBO 100 Microscope Illuminating System may only be handled by trained personnel. To ensure that the illuminating system functions properly with the microscope, the appropriate microscope manual must be observed. In addition, observe the manual "HBO 100 ­ Electronic ballast". Special regard must be paid to the notes on instrument safety included in this manual. The data sheets from the lamp manufacturers must be observed when the HBO 103 lamps are operated. To guarantee the safe operation and function of the HBO 100 Microscope Illuminating System, it is necessary under any circumstances to take the precautions and observe the warnings contained in the operating instructions. 1. 2 Regulations concerning Instrument Safety and Electromagnetic Compatibility (EMC) The following warning and information symbols are used in this manual: The HBO 100 Microscope Illuminating System has been designed, produced and tested in compliance with EN 61010, Part 1 (VDE 0411). The illuminating system meets the requirements of EC directives 73/23 and 89/336 and the EMC legislation, as amended on September 18, 1998. Radio-noise suppression complies with EN 55011, Class B, noise immunity with EN 61326. Compliance with the EC directives mentioned is documented by the CE certificate. 4 B 46-0063 e 03/06 Microscope Illuminating System HBO 100 Safety Unpacking, Use Carl Zeiss 1. 3 Notes on Unpacking, Transport and Storage 1. 4 Hints on Use The lamps may be removed from the package only if the protection mask (Cat. For safety reasons, a safety holder is inserted in the microscope illuminator instead of the bulb during transport. Both the HBO 100 microscope illuminator and the HBO 103 lamp must be transported in their original packaging. 1 HBO 100 Microscope Illuminating System (manual adjustment) Lamp Transformer Line cable Table: Catalogue numbers 1 2 3 4 Lamp, top part Line cable Transformer for HBO 100 Connecting cable 5 Lamp, bottom part 6 Dovetail 7 Heat-protection filter Fig. 2 HBO 100 Microscope Illuminating System, self-adjusting 8 B 46-0063 e 03/06 Microscope Illuminating System HBO 100 Instrument Description Technical Data Carl Zeiss 2. 2 Technical Data of the Microscope Illuminating Systems HBO 100 illuminator Cat. 423011-9901 Lamp housing Length Width Height Connection to stand Connection to transformer Transformer 165 mm 166 mm 205 mm dovetail Cable with special plug Transformer for HBO 100 Cat. No. 432604-9901 100-240 V AC 50-60 Hz 155 VA F1/F2 2x T 2 A/H Mercury vapor short-arc lamp OSRAM Type HBO 103 W/2 Cat. 380301-9350-000 OSRAM Type HBO 100 W/2 Type HBO 103 W/2 Line connection Line frequency Power consumption Fuse Lamp For the technical data of the lamps please see the information provided by the manufacturer. Recommended: Average life of the lamps 200 h 300 h B 46-0063 e 03/06 9 Carl Zeiss Instrument Description Technical Data, Line spectrum Microscope Illuminating System HBO 100 Fig. 3 Line spectrum of the HBO 100/103 mercury short-arc lamps 10 B 46-0063 e 03/06 Microscope Illuminating System HBO 100 Start-Up Lamp Insertion and Change Carl Zeiss 3 3. 1 Start-Up Lamp Insertion and Change - Before inserting the lamp, make sure the illuminating system has been disconnected from line power. By doing so, the electric connection is established and the heat sink clamped. Do not exert any force to the lamp, when attaching the heat sink. 4/2) on the bottom part of the illuminator oppositely to the direction indicated by the arrow as far as it will go. · Turn the control knob of the collector back to mid position, if necessary. 12 B 46-0063 e 03/06 Microscope Illuminating System HBO 100 Start-Up HBO 100 Carl Zeiss 3. 2 Start-Up of HBO 100 Microscope Illuminating System Do not look directly into the lamp or its reflected light. Procedure: · Install the HBO 100 microscope illuminator on the microscope (see Operating Manual of microscope). [. . . ] If the adjustment fails again, check whether the lamp has been inserted correctly in the base of the HBO 100 (pushed in as far as it will go). For this, refer to Section 3. 1. 1 LED key 2 Collector control knob Fig. 9 Adjustment of HBO 100, self-adjusting B 46-0063 e 03/06 15 Carl Zeiss Start-Up Setting Offset Values Microscope Illuminating System HBO 100 3. 5 Setting Offset Values on HBO 100 Microscope Illuminator, self-adjusting (423011-9901) On the self-adjusting illuminator, the position of the lamp arc and its mirror image may be individually customized, if required, by the adjustment of offset values. By briefly pressing the recessed keys on the rear side of the illuminator housing (Fig. [. . . ]