User manual ZANKER ZKT3110S 68D

[. . . ] · Do not place or store flammable liquids, highly inflammable materials or fusible objects (e. g. plastic film, plastic, aluminium) on or near the appliance. How to avoid damage to the appliance · The glass ceramic can be damaged by objects falling onto it. · The edge of the glass ceramic can be damaged by being knocked by the cookware. [. . . ] Control panel Switch on the appliance Touch of the front right cooking zone and at the same time Touch Display l / h (if hot) 4 x ¾ or h Decimal points flash Appliance switches off. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Control panel Switch on the appliance Touch at the same time Display l / h (if hot) of the front right cooking zone and 4 x ¾ Decimal points flash Until the appliance is next switched off, it can used as normal. 8 Safety cut-out Cooking surface · If after switching on the appliance a heat setting is not set for a cooking zone within approx. · If one or more sensor fields are touched for longer than approx. ER03 flashes on the display or changes to h if there is still residual heat. · If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. a wet cloth) or liquid boiling over onto the control panel switches all cooking zones off. Cooking zones · If one of the cooking zones is not switched off after a certain time, or if the heat setting is not modified, the relevant cooking zone switches off automatically. Heat setting 1-2 3-4 5 6-9 6 hours 5 hours 4 hours 1. 5 hours Switches off after 9 Tips on Cooking and Frying 3 Information on acrylamides According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures and not browning foods too much. Cookware · You can recognise good cookware from the bottoms of the pans. · Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the glass ceramic surface which are difficult or impossible to remove. Energy saving 2 2 2 2 Always place cookware on the cooking zone before it is switched on. If possible, always place lids on the pans. Switch cooking zones off before the end of the cooking time, to take advantage of residual heat. Bottom of pans and cooking zones should be the same size. 10 Examples of cooking applications The information given in the following table is for guidance only. 3 Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 12 What to do if . . . Problem The cooking zones are not functioning. Possible cause No cooking zone selected Remedy Select cooking zone within 10 seconds of switching on (Decimal point lights up) More than 10 seconds have passed Switch on the appliance again. The cooking zones cannot be selected / Appliance does not react to since the appliance was switched Select cooking zone within 10 seconds of switching on on the control panel input l The child safety device is activated Deactivate the child safety device (See section "Child safety device") The sensor fields are partly covered Remove the cloth or the liquid by a damp cloth or with liquid Safety cut-out has been triggered The residual heat indicator is not displaying anything Switch on the appliance again The cooking zone was only on for a If the cooking zone is supposed to short time and is therefore not hot be hot, call the Customer Service Department. Several sensor fields were touched Only touch one sensor field at the same time Safety cut-out due to overheating Let the appliance cool down. Disconnect the appliance from the electrical supply and have it connected properly Separate the appliance from the mains for a few minutes (remove the mains fuse). [. . . ] · If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°; or higher). A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm. Suitable isolation devices include line protecting cutouts, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors. 1 IMPORTANT! 15 16 Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section "What to do if. . . "). [. . . ]