User manual ZANKER ZKDW24

[. . . ] If in the rinse aid dispenser there is still rinse aid you must wait until it has finished before using detergent that contains rinse aid. If you are using dishwasher detergent and rinse aid separately, the rinse aid is to be put into the rinse aid dispenser. - In this case the rinse aid dosage must be set in position from 1 to 6 (see "Adjusting the dose") and the rinse aid indicator light activated. q Filling with rinse aid (Rinse aid dispenser type A) SR14 1. Fill with rinse aid exactly up to the level indicator marked "max". The salt container will require topping up periodically. [. . . ] All programmes with prewash need an additional detergent dose (5 g) that must be placed over the lid of the dispenser. This detergent will take effect during the prewash phase. 37 Maintenance and cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc. . . . ). Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run a 65°C wash programme without dishes using detergent. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. To ensure a correct working of the dishwasher, NEVER try to remove the upper spray arm. If residues of soil have clogged the holes in the upper spray arm, remove them with a toothpick. MA33 Cleaning the filters The filters in the base of the washing compartment are to a large extent self-cleaning. Nevertheless the filters should be checked and cleaned from time to time. The dishwasher filter system comprises a coarse/fine filter (A/B), a microfilter (C) and a flat filter (D). Some dishwasher models filter system comprises only a coarse filter (A), a microfilter (C) and a flat filter (D). Unlock the filter system using the handle on the microfilter, and remove. Prolonged periods of non-operation If you are not using the machine for any period of time you are advised to: 1. Leave the door ajar to prevent the formation of any unpleasant smells. Leave the inside of the machine clean. Frost precautions MA35 MA32 3. Turn the handle about 1/4 a turn anticlockwise and remove. Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc. . . . ): 1. Take hold of the coarse/fine filter (A/B) by the handle with the hole and remove from the microfilter (C). Remove the flat filter (D) from the base of the washing compartment and clean both faces thoroughly. MA31 7. Put the flat filter back in the base of the washing compartment. 38 What to do, when. . . Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. . . . there are problems when operating the dishwasher The dishwasher will not start or stops during operation. Press the On/Off push button to switch the dishwasher off and carry out the following suggested corrective actions. Malfunction The machine does not fill with water. Possible cause The water tap is blocked or furred with limescale. The filter (where present) in the threaded hose fitting at the water inlet valve is blocked. [. . . ] 40 Electrical connection Information concerning the electrical connection is given on the rating plate on the edge of the dishwasher's door on the right. Before plugging the appliance into the wall socket, make sure that: 1. The mains voltage and current rating at the site of installation match the nominal voltage and current rating given on the rating plate. The meter, fuses, mains power supply and wall socket can all take the maximum load required. [. . . ]