User manual ZANKER ZANKER4635

[. . . ] Serious damage can occur to the product and to property if this is not adhered to. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. [. . . ] This is particularly important if you are using 13 fabric conditioner to avoid the conditioner entering the machine prematurely. When using liquid detergent and a prewash programme, place the detergent into the correct compartment in the dispenser drawer, after the prewash has finished. Washing Programmes Programmes for cotton and linen Wash programme/ Washing symbol WHITES + PREWASH Degree of soil and type of laundry Programme dial position Description Possible options Max Progr. Prewash at 40 °C Wash at 90°C QUICK WASH 4. 5 kg HALF LOAD 3 rinses Long spin For heavy soiled cotton items. A 145 WHITES White cotton, for example normally soiled work garments, sheets, household linen, underwear, towels. B Wash at 90 °C 3 rinses Long spin QUICK WASH 4. 5 kg HALF LOAD 120 Fast coloured cotton or FAST COLOUREDS linen fabrics, shirts, underwear, towels. Non fast coloured NON- FAST cotton or linen fabrics, COLOUREDS shirts, blouses, underwear. HAND RINSES Separate rinse cycle for hand washed cotton and linen items Separate spin for cotton and linen items C(*) Wash at 60 °C 3 rinses Long spin QUICK WASH HALF LOAD 4. 5 kg 135 D F G Wash at 40 °C 3 rinses Long spin QUICK WASH HALF LOAD 4. 5 kg 115 4 rinses Long spin 4. 5 kg 58 LONG SPIN Long spin 4. 5 kg 12 (*) This programme at 60°C with cold water filling and a wash load of 4. 5 kg is the reference programme for the Energy label according to EEC Directive 92/75. Water filling: 30°-30°-40° programmes: cold water filling 50°-60° programmes: hot and cold filling 95° programme: hot water filling The programme times are intended as a guide only. The actual time will vary depending on incoming water temperature and pressure. When a programme is selected, the selector dial will advance to the water filling position. The appliance takes in water and the selector will appear to move to the C position. The appliance will have memorised the programme selected, in this case B, and will run the correct programme even though the selector dial appears to be at position C. · We recommend you not to switch the appliance off and on during its operation. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the pump cover, after a cleaning inspection, ensure it is securely retightened so as to stop leaks and young children being able to remove it. Cleaning the water inlet filters If your water is very hard or contains traces of lime deposit, the water inlet filters may become clogged. 17 Something Not Working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom The machine does not start Possible causes q q q q q q The door has not been closed. There is no supply at the socket The main fuse or the fuse in the plug has blown. The wash load is unbalanced: redistribute the clothes inside the drum to allow the machine to spin. Too much detergent or unsuitable detergent has been used (creates too much foam). Check whether there are any leaks from one of the inlet hose(s) fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. An insufficient amount of detergent leaves the laundry looking grey and causes lime scale to form. [. . . ] Use the plastic "U-Piece" supplied. P0022 When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90cm (35. 4'') and no less than 60cm (23. 6'') above floor level. The upright standpipe should have a minimum length of 30cm (12'') from the bottom of the elbow to the top of the pipe (see diagram). The drain hose must not be kinked. Important q q Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. For a correct functioning of the machine the drain hose must be hooked on the proper support piece situated on the top of the back side of the appliance. 3 pin Max. 90 cm. (35. 4") P1039 Make sure that it is designed in such a way, that the end of the drain hose cannot be covered with water. Min. 60 cm. [. . . ]