User manual ZANKER WF2050

[. . . ] You MUST read it carefully before installing or using the appliance. Installation q q Check your dishwasher for any transport damage. For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. Any electrical and plumbing work required to install this appliance should be carried out by a qualified and competent person. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. [. . . ] Fill the rinse aid dispenser Filling with salt Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion. The water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. Water hardness is measured in equivalent scales, German degrees, French degrees and PPM (parts per Million). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. Open the door, remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise. Pour 1 litre of water inside the container (this is necessary only before filling with salt for the first time). Using the funnel provided, pour in the salt until the container is full. Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket. Prior to the start of a wash programme (not for the "Rinse and Hold" programme, that does not require the use of detergent). Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. Fill with detergent 1. The marking indicates the dosing levels: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent 3. All programmes with prewash need a little amount of detergent (5/10 g) to be added in the adjacent chamber (3). In case that plates are loaded in the upper basket: load them starting from the rear positions of the basket; tilting them slightly forwards and avoiding the front positions near the door. US71 Before closing the door, ensure that the spray arms can rotate freely. Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in upper basket lower basket DE19 DE22 4. Close the lid and press until it locks in place. With upper basket raised With upper basket lowered 20 cm 24 cm 31 cm 27 cm To move to the higher position proceed as follows: 1. Move the front runner stops(A) of the upper basket outwards and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. When the basket is in the higher position you will not be able to use the cup rack(s). RC01 After loading your machine always close the door, as an open door can be a hazard. 25 Different kinds of detergent Detergent tablets Detergent tablets of different brands dissolve at different speeds. For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programmes. Therefore please use long programmes when using detergent tablets, to ensure the complete removal of detergent residuals. Do not place the tablets in the tub or in the cutlery basket as this will result in poorer wash results. The tablets should be placed in the detergent dispenser. Use of "3 in 1" combi detergents General advice These products are detergents with integrated and combined detergent/rinse-aid and salt functions. [. . . ] Take hold of the coarse/fine filter (A/B) by the handle with the hole and remove from the microfilter (C). Remove the flat filter (D) from the base of the washing compartment and clean both faces thoroughly. MA31 7. Place the coarse/fine filter (A/B) in the microfilter C) and press together. Put the filter combination in place and lock by turning the handle clockwise to the stop. [. . . ]