User manual ZANKER KSU330A

[. . . ] Once your unit is installed, keep the Use and Care Guide and this Installation Guide in a safe place for future reference. Black and White units have a reversible door with a slightly contoured handle across the top. They come with a flush mounted door panel that, when removed, will accept a custom 1/4-inch thick door panel or a 3/4-inch thick full overlay door panel. Stainless Steel units are covered with a protective coating and have been ordered left- or righthand hinged. [. . . ] · If the ambient temperature is expected to drop below 45°F (7°C), drain all water from the unit to prevent freezing damage not covered by the warranty. · For best performance, keep the unit out of direct sunlight and away from heat generating equipment. · For best performance and life outdoors, place under a counter or provide shelter of some kind. · In climates where high humidity and dew points are present, condensation may appear on outside surfaces. The condensation will disappear when the humidity drops. 2 ULIN_0003_A Figure 7 Figure 8 5. Remove existing bottom hinge (3 screws) and remount on opposite side TOP. Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location. With bottom of door facing up, remove pivot plate (2 screws), flip over, and remount on opposite side of door (see Figure 9). Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (see Figure 10). Tilt top of door into position in top hinge and install top hinge screw pin. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom). Figure 10 www. U-LineService. com 6 08/2006 2115R -- Refrigerator Side-By-Side Installation Instructions For a complete refreshment center, install your 2115R Refrigerator beside a U-Line Ice Maker, Combo, or Wine Captain Model (see Figure 11 for typical cut-out). Replace the Overlay Handle and secure with the two screws removed in Step 4 under Removing Existing Door. Attach Overlay cap to door, opposite side of where hinges will be (see Figure 23). Overlay Cap Figure 20 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in Figure 21. The spacers allow the original door panel to slide back into the 1/4"-thick door reveal (channel). 3/4" Wood Panel Replacement Handle Figure 23 www. U-LineService. com 10 08/2006 2115R -- Refrigerator 4. Use the two #8-32 x 1/2" Flat Head Phillips screws (Black) supplied with kit (see Figure 24). #8-32 x 1/2" Flat Head Screws Black, Two Places 3/4" Wood Overlay Top Pivot Plate Screw to attach Handle Removed in step 4 Door Closure Top Boss Existing Door Door Closure Bottom Boss Pivot Post #8-32 x 1/2" Flat Head Screw Three Places Wood Panel Bottom Hinge Plate (5/8" Longer than Existing Bottom Hinge Plate) Figure 24 Figure 26 5. Starting at the corners and working toward the center, push the door gasket back into place. Remove the existing hinges from the unit, saving the door closure assembly. Install the new Replacement Top Hinge onto the unit (see Figure 25). Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) Pivot Post IMPORTANT Pivot posts must be cleaned. Position door and install the pivot post into the top hinge (using the Phillips screwdriver). Reinstall the door shelves by lining up the bosses and first pushing straight in, then down at a 45° angle. #8-32 x 1/2" Flat Head Screw Three Places Top Pivot Plate Figure 25 Door Panel ULIN_0405 3. [. . . ] Mount the door, install top hinge pivot pin and go on to 6 Prepare Power Supply. Door Closer Inserts Adjusting Door Alignment 1. Remove top hinge screw pin (7/64" Allen wrench or Phillips screwdriver, depending on your unit's construction, see Figure 28). With door upside-down, loosen but do not remove the two screws on the door's bottom hinge plate. Boss Figure 30 Figure 28 ULIN_0133_A www. U-LineService. com 12 08/2006 2115R -- Refrigerator 6 Prepare Power Supply 7 Level the Unit Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. [. . . ]