User manual YAMAHA YST-SW90
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual YAMAHA YST-SW90. We hope that this YAMAHA YST-SW90 user guide will be useful to you.
Manual abstract: user guide YAMAHA YST-SW90
Detailed instructions for use are in the User's Guide.
[. . . ] When not planning to use this unit for long periods of time
(i. e. , vacation, etc. ), disconnect the AC power plug from the wall outlet.
8. To prevent lightning damage, disconnect the AC power
plug when there is an electrical storm.
9. Since this unit has a built-in power amplifier, heat will
radiate from the rear panel. Therefore, place the unit apart from the walls, allowing enough space above, behind and on the both sides of the unit to prevent fire and damage. [. . . ] · This unit can be connected to either the speaker terminals or the line output (pin jack) terminals of the amplifier. Choose one of the connections shown below according to your audio system. Refer also to the owner's manuals supplied for your audio system.
CONNECTING TO SPEAKER TERMINALS OF THE AMPLIFIER Using one unit
When your amplifier has one set of speaker terminals · Disconnect your main speakers from the amplifier if connected, and connect them to the speaker terminals of this unit. Illustrations of the unit used in this manual are of YST-SW160 unless mentioned otherwise.
Right speaker
OUTPUT TO SPEAKERS
INPUT2
AUTO STANDBY
PHASE
BASS
Left speaker
This unit
FROM AMPLIFIER INPUT1
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
LOW
HIGH
NOM
REV
MOVIE MUSIC
OFF
LOW
HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
OFF
Amplifier
POWER
ON OFF
To AC outlet Speaker terminals When your amplifier has two sets of speaker terminals This unit
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
OUTPUT TO SPEAKERS
INPUT2
AUTO STANDBY
PHASE
BASS
LOW
HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
OFF
LOW HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
POWER
ON OFF
OFF
Right speaker To AC outlet
Left speaker
Amplifier Speaker terminals
A B
(Both A and B speaker outputs must be ON. )
4
English
Using two units
Disconnect your main speakers from the amplifier if connected, and connect them to the speaker terminals of this unit.
Right speaker
Left speaker
OUTPUT TO SPEAKERS
INPUT2
AUTO STANDBY
PHASE
BASS
OUTPUT TO SPEAKERS
INPUT2
AUTO STANDBY
PHASE
BASS
This unit
LOW HIGH NOM REV MOVIE MUSIC LOW HIGH NOM REV MOVIE MUSIC
This unit
FROM AMPLIFIER INPUT1
OFF
FROM AMPLIFIER INPUT1
OFF
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
OUTPUT TO SPEAKERS
INPUT2
AUTO STANDBY
PHASE
BASS
LOW
HIGH
NOM
REV
MOVIE MUSIC
LOW
HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
OFF
FROM AMPLIFIER INPUT1
OFF
Amplifier
POWER
ON OFF
POWER
ON OFF
To AC outlet Speaker terminals
To AC outlet
Connecting to this unit's OUTPUT/INPUT terminals
For connections, keep the speaker wires as short as possible. (Cut the excessive wire, if necessary. ) If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, by observing + and markings. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the core of the speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit, your amplifier and/or speakers. Simply insert the Banana Plug connector into the corresponding terminal.
How to Connect: Red: positive (+) Black: negative ()
1 Unscrew the knob. 5 mm (1/4") insulation from the speaker wires. ] 3 Tighten the knob to secure the wire firmly.
5
CONNECTING TO LINE OUTPUT (PIN JACK) TERMINALS OF THE AMPLIFIER
· Connect the main speakers to the speaker output terminals of the amplifier. · Amplifier line output terminals are generally labeled PRE OUT or SUBWOOFER OUT. · To connect with a YAMAHA DSP amplifier, connect the SUBWOOFER (or LOW PASS etc. ) terminal on the rear of the DSP amplifier to either the left (L) or right (R) INPUT 2 terminal.
Using one unit
Left speaker This unit
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
OUTPUT TO SPEAKERS
INPUT2
AUTO STANDBY
PHASE
BASS
Right speaker
LOW
HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
OFF
LOW HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
POWER
ON OFF
OFF
To AC outlet
<YAMAHA DSP amplifier>
SUBWOOFER
Pin plug cords
Amplifier
<Amplifier>
PRE OUT
Using two units
Left speaker
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
Right speaker
LOW
HIGH
NOM
REV
MOVIE MUSIC
LOW HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
OFF
FROM AMPLIFIER INPUT1
OFF
This unit
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
This unit
OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS
Pin plug cords
LOW
HIGH
NOM
REV
MOVIE MUSIC
LOW
HIGH
NOM
REV
MOVIE MUSIC
FROM AMPLIFIER INPUT1
OFF
FROM AMPLIFIER INPUT1
OFF
POWER
ON OFF
POWER
ON OFF
Amplifier
To AC outlet
To AC outlet
Notes on the above connections · When connected to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of the subwoofer. · When connecting this unit to a monaural line output terminal of the amplifier, connect to either the left or right INPUT 2 terminal. * There may be a case that the power turns on unexpectedly by sensing noise from other appliances. * The level of low frequency input signal differs with each source, and each different part on the same source. This function is available only when the power of this unit is on (by setting the STANDBY/ON button Y to ON).
¤ AUTO STANDBY switch
With this switch, you can activate the Automatic Standby function. * Change the setting of this switch only when the power of this unit is on standby (by setting the STANDBY/ON button to OFF).
# PHASE switch
Normally this switch is to be set to the REV (reverse) position. However, according to your speaker systems or the listening condition, there may be a case when better sound quality is obtained by setting this switch to the NOM (normal) position. Select the better position by monitoring the sound.
< BASS switch
YST-SW160 only
By setting this switch to the MOVIE position, the bass sound in video software is well reproduced. By setting it to the MUSIC position, the bass sound in audio software is well reproduced.
7
ADJUSTING VOLUME
Adjustment of the HIGH CUT control, the VOLUME control and the PHASE switch needs to be changed according to the main speakers, listening condition, source, etc.
Front panel
Rear panel
PHASE
YST-SW160
STANDBY/ON HIGH CUT VOLUME
YST-SW90
STANDBY/ON HIGH CUT VOLUME
NOM
REV
40 Hz
140 Hz
0
10
50 Hz
150 Hz
0
10
3 1 2 3 4 5
5
1, 6
3
5
1, 6
7
Set the VOLUME control to minimum (0). Play any source and adjust the amplifier's volume control to the desired listening level. Adjust the HIGH CUT control according to the main speakers connected.
Normally, set the control to the main speaker's rated minimum reproducible frequency*. [. . . ] 50 Hz150 Hz (24 dB/oct. ) Frequency Response . . . . . . . . . . . . . . . . . . . . . AC 110/120/220/240 V, 50/60 Hz (Adjustable with Voltage Selector)
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 mm × 485 mm × 409 mm (9-5/16" × 19-1/8" × 16-1/8") Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 oz. )
* Design and specifications are subject to change without notice.
11
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE. , BUENA PARK, CALIF. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA YST-SW90
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA YST-SW90 will begin.