User manual YAMAHA XP-3500

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual YAMAHA XP-3500. We hope that this YAMAHA XP-3500 user guide will be useful to you.


YAMAHA XP-3500 : Download the complete user guide (7885 Ko)

You may also download the following manuals related to this product:

   YAMAHA XP-3500 (7965 ko)
   YAMAHA XP-3500 (7966 ko)
   YAMAHA XP-3500 (7970 ko)
   YAMAHA XP-3500 (8154 ko)

Manual abstract: user guide YAMAHA XP-3500

Detailed instructions for use are in the User's Guide.

[. . . ] POWER AMPLIFIER EN DE FR ES Español OWNER'S MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE INSTRUCCIONES Français Deutsch English FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. [. . . ] If the amplifier has been set to STANDBY mode, the indicator is lit in orange. Lights up green when the corresponding channel's output level exceeds 2 Vrms (equivalent to 1/2 W into an 8 load, or 1 W into a 4 load). 6 Volume control knobs Each control knob adjusts the volume of the corresponding channel, in 31 steps from - dB to 0 dB. * If you wish to lock in the knob settings, you can fasten the supplied security cover over the knobs so that the settings will not be disturbed. 2 TEMP indicator Lights up red if the heat sink temperature exceeds 85°C (185°F). 3 PROTECTION indicator When the protection system is active, the PROTECT indicator light up in red and the speakers are automatically disconnected from the amplifier's outputs. The protection system activates in the following situations: When the amplifier is turned on The protection system activates for approximately three seconds when the amplifier is turned on. After three seconds, the protection system deactivates automatically and the amplifier is ready for normal operation. If a DC voltage is detected at the amplifier's outputs How to install the security cover (1) Use the supplied hex wrench to remove the four attachment screws from the amplifier. Fasten it into place using the same screws. XP7000/5000: Power shut down and the indicator is not lit. Once the DC voltage problem is corrected, the protection system deactivates automatically and the amplifier is ready for normal operation. If the amplifier overheats 7 Air intakes The amplifier uses forced-air cooling. The cooling fans draw air in from the front and exhaust it through the rear. Please be sure that you do not block the air intakes or exhaust vents. * The fans do not come on at initial power-on, but will switch on automatically when the temperature of the heat sink rises above 50°C (122°F). The fan speed will then vary automatically as the temperature changes. Front Rear When overheating occurs, the PROTECT/MUTE indicator lights. You should immediately turn off the amplifier and allow it time to cool down. See the Precautions section of this Owner's Manual for ways to prevent the amplifier from overheating. 4 CLIP indicator Lights up red when the output signal distortion on the corresponding channel rises above 1% -- indicating that "clipping" has occurred bacause the signal level is too high. Air intake Air exhaust 6 XP7000/XP5000/XP3500/XP2500/XP1000 Owner's Manual Rear Panel 4 3 5 6 7 1 1 XLR inputs connectors 2 7 5 MODE switch 8 These balanced XLR-3-31 type connectors are used to connect input signals. The pins are wired as shown below (IEC 60268). Hot Ground Cold * In bridged mode, only the first channel in the pair is active; i. e. , channel A of pair A/B. Make sure not to input an audio signal to an inactive input terminal. · STEREO mode In STEREO mode, channels A and B are completely independent. · PARALLEL mode In PARALLEL mode, the channel A input signal is sent both to the channel A power amp and the channel B power amp. In this case, loads are automatically connected between the A and B input terminals. · BRIDGED mode In BRIDGED mode, channels A and B operate simultaneously, functioning as a single mono amplifier. Note: When in PARALLEL and BRIDGED modes, input terminals A and B are shorted automatically. Make sure not to input an audio signal to an inactive input terminal. 2 Euroblock connectors These balanced Euroblock connectors are used to connect input signals. 6 MONITOR/REMOTE terminals This terminal is used to connect the external device for monitoring or remote control. Refer to "MONITOR/ REMOTE PIN layout" on page 15. 3 HPF switches These switches are used to turn on and off the HPF (High Pass Filter) for each channel. When this is set to 20Hz or 55Hz, frequencies below the respective settings are filtered using a 12 dB/octave high pass filter. 7 SPEAKERS terminals 1: These 5-way binding posts are used to connect speakers. Speakon type cable plugs can be connected here. 4 GAIN switch This switch is used when changing the Gain of the A and B channels simultaneously. · +4dBu: The maximum output power can be obtained when +4dBu is input. · 26dB: Setting of 26dB · 32dB: Setting of 32dB 8 GND terminal If you are having a problem with hum or noise, use this terminal to connect to ground (earth) or to connect to the chassis of a mixer, preamp, or other device in your system. XP7000/XP5000/XP3500/XP2500/XP1000 Owner's Manual 7 Speaker Connections Speakers can be connected to the amplifier in three ways, as shown below. Note that speaker impedance will vary according to the connection method and the number of speakers. [. . . ] Inrush current XP7000, XP5000: XP3500: XP2500: XP1000: 11A (100V), 13A (120V), 25A (240V) 11A (100V), 13A (120V), 22A (240V) 10A (100V), 12A (120V), 20A (240V) 9A (100V), 11A (120V), 14A (240V) 18 XP7000/XP5000/XP3500/XP2500/XP1000 Owner's Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Europe GmbH Branch Sp. z o. o. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA XP-3500




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA XP-3500 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.