User manual YAMAHA WIRELESS DCP

[. . . ] • Future upgrades of the Wireless DCP application and any changes in specifications and functions will be announced separately. EN Wireless DCP Owner’s Manual 1 Contents 1. System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (However, only one device can be logged into by an administrator password. ) 4. Connect the MTX processor to the LAN connector of the Wi-Fi access point. If you connect to a WAN (Internet) connector, the smart device will not be able to communicate properly with the MTX processor. Wireless DCP Owner’s Manual 8 3. Configuration 3. 3 Wireless DCP Tap the Wireless DCP app to launch it. The Select Device screen will be displayed. Device list MTX processors available for connection are displayed here. When you select one, the Enter Password screen will be displayed. DEMO button Tap DEMO on this screen to activate Offline Demo mode. In this mode, you can try out Wireless DCP functions and the user interface without performing any actual operations on the MTX processor. If you launch Wireless DCP with Auto-connect mode active, the app will automatically reconnect to the MTX processor it was most recently used with. Refer to Section 3. 3. 3 Entering a Password for details. Wireless DCP Owner’s Manual 9 3. Configuration  3. 3. 1 Offline Demo Mode In Offline Demo mode, Wireless DCP disconnects from the MTX processor so you can try out the app’s functions and user interface without performing any actual operations. To activate this mode, tap DEMO on the Select Device screen. Controller pane Use this pane to try out the faders and buttons. Page button Tap to display the Select Page screen. Controller 1 and Controller 2 buttons Tap to switch the Controller pane’s display. Settings button Tap to display the Settings screen. Wireless DCP Owner’s Manual 10 3. Configuration  From Demo mode to Normal mode On the Settings screen, tap Select Device. . . When you do so, the Enter Password screen will be displayed. Wireless DCP Owner’s Manual 11 3. Configuration  3. 3. 2 Making Connections On the Select Device screen, tap the MTX processor to be controlled. When you select a processor, the Enter Password screen will be displayed. Information displayed Upper line: Device name (configured using MTX Editor) Lower line: Unit ID and model name Wireless DCP Owner’s Manual 12 3. Configuration  3. 3. 3 Entering a Password Enter a valid password to connect to the selected MTX processor. Reset button Tap to display the Reset Password screen. Cancel button Tap to return to the Select Device screen without entering a password. 1 Auto-connect switch Turn this switch on to connect automatically whenever the app is launched. 2  To enter a password 1. Upon connection, the Controller 1 pane will be displayed. NOTE Passwords take the form of a four-digit number, and none are set when the app is first launched. In this condition, it is possible to log into Wireless DCP without entering a password by simply tapping Join. Refer to Section 5. 3 Changing Passwords for details. Wireless DCP Owner’s Manual 13 3. Configuration There are two different types of password—one for administrator, one for staff. As shown below, certain functions are available only when logged into the MTX processor using an administrator password. Administrator Select Page Change Password Edit Staff Pages    Staff  (but restricted by administrator) × × NOTE You can restrict the functions for staff use by assigning different passwords for administrator and staff. Wireless DCP Owner’s Manual 14 3. If, for example, you forget a password, you can use this screen to reset (or remove) it. Note that both administrator and staff passwords are reset by this action. Enter the MAC address of the MTX processor to connect using the keyboard. [. . . ] For details, contact the device's dealer.  To disable automatic connection 1. As described in To connect to a different device (page 21), select the MTX processor being controlled. Automatic connection will be disabled when the Enter Password screen is displayed. In addition, automatic connection is also disabled if Cancel is tapped to return to the Select Device screen from the Enter Password screen.  No MTX processor in the device list If no Wireless DCP settings have been registered in any MTX processor presets, the device list will not contain any devices. [. . . ]