User manual YAMAHA VXS8/VXS8W/VXS5/VXS5W

[. . . ] Malfunction or fire may occur especially when the following sounds or noises are generated: - feedback, when using a microphone - continuous and extreme volume sound from a musical instrument - extreme continuous distorted sound - noise caused by plugging/unplugging the cable while the amplifier is turned on SPECIFICATIONS Type Component VXS5/VXS5W 2-way, Bass-reflex 8" (20 cm) Cone driver 5-1/4" (13 cm) Cone driver 1" (2. 5 cm) Soft dome tweeter 3/4" (2 cm) Soft dome tweeter 100° H × 100° V 120° H × 120° V 8Ω 90 W 75 W 180 W 150 W 360 W 300 W 91 dB SPL 89 dB SPL 117 dB SPL 114 dB SPL 51 Hz – 20 kHz 62 Hz – 20 kHz 2. 8 kHz 3 kHz Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-) Max. wire size 12 AWG (2. 5 mm2) 60 W, 30 W, 15 W, 7. 5 W 30 W, 15 W, 7. 5 W, 3. 8 W 60 W, 30 W, 15 W 30 W, 15 W, 7. 5 W Full-range power limiting to protect network and transducers No IP35 Rectangle ABS PC/ASA Powder coated perforated aluminum (t=1 mm) Aperture ratio: 51% VXS8/VXS5: Black (Not painted, approximate value: Munsell N3) VXS8W/VXS5W: White (Not painted, approximate value: Munsell 9. 3) 278 × 430 × 239 mm 176 × 280 × 163 mm (10. 9" × 16. 9" × 9. 4") (6. 9" × 11. 0" × 6. 4") 8. 2 kg (18. 1 lbs) 3. 6 kg (7. 9 lbs) Packaged in pair VXS8/VXS8W NOTICE To avoid the possibility of malfunction/damage to the product or damage to other property, follow the notices below. Location • Do not place the device in an unstable position where it might accidentally fall over. [. . . ] Before turning the power on or off for all devices, set all volume levels to minimum. • Use only speaker cables for connecting speakers to the speaker connectors. Use of other types of cables may result in fire. Maintenance • Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and do not use electrical contact cleaner. These may damage the outer packaging and dissolve the parts. ● About This Manual The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device. *1: Pink noise with 6 dB crest factor. *2: Half-space (2π) *3: Calculated based on power rating and sensitivity, exclusive of power compression. *4: When connecting with low impedance *5: IP34 when installing the speaker to the ceiling vertically. Specifications and descriptions in this owner’s manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. The dimensions are shown overleaf. INSTALLING THE SPEAKERS Install the speakers onto the wall/ceiling with the supplied brackets. Pre-installation (Preparation of the cable) Use stranded wire for cables attached to the Euroblock connector. Strip their insulation as shown in the figure and connect them. About 7 mm (0. 3 in. ) 2 CONNECT THE WIRING TO THE CONNECTOR 1 Remove the Euroblock connector. 3 SET THE LINE VOLTAGE/IMPEDANCE AND POWER Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/ 70V line distributed system, by rotating the tap selector switch on the rear side of the speaker with a flat-blade screwdriver. 2 Attach the safety pin. Be sure to attach the safety pin to prevent the mounting bracket from falling. Euroblock connector Illustration indicates the setting at 30 W for 100 V line and 15 W for 70 V line. Safety pin NOTE Do not plate stranded wires by solder. [. . . ] This can be useful to identify which speaker has a problem. Angle adjustment bolt Safety wire Stopper screw (VXS8/VXS8W only) 4 Attach the terminal cover. Terminal cover Horizontal installation Stopper screw (VXS8/VXS8W only) Angle adjustment bolt Horizontal From amplifier or previous speakers NOTE Mounting bracket can be attached in reverse direction. To subsequent speakers To subsequent speakers 5 (If installing the speaker to the wall) turn the speaker horizontally to set the angle. 6 Make sure the mounting bracket is seated against the bracket base, then tighten the supplied bolt (indication of torque: 6. 5 N·m). 2 Set the desired vertical angle of the speaker. [. . . ]