User manual YAMAHA VXC4

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual YAMAHA VXC4. We hope that this YAMAHA VXC4 user guide will be useful to you.


YAMAHA VXC4 : Download the complete user guide (4588 Ko)

You may also download the following manuals related to this product:

   YAMAHA VXC4 (4743 ko)
   YAMAHA VXC4 (4574 ko)
   YAMAHA VXC4 (4577 ko)
   YAMAHA VXC4 (4586 ko)
   YAMAHA VXC4 (4583 ko)
   YAMAHA VXC4 (1350 ko)
   YAMAHA VXC4 (4726 ko)

Manual abstract: user guide YAMAHA VXC4

Detailed instructions for use are in the User's Guide.

[. . . ] Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. Water warning • Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, have the device inspected by qualified Yamaha service personnel. NOTICE To avoid the possibility of malfunction/damage to the product, damage to data, or damage to other property, follow the notices below. Grille Shape Back Can Material Baffle Material Material CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. [. . . ] *2: Half-space (2π) *3: Calculated based on power rating and sensitivity, exclusive of power compression. DIMENSIONS Unit: mm VXC4/VXC4W O-ring 195 182 Connections • Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Use only speaker cables for connecting speakers to the speaker jacks. Use of other types of cables may result in fire. 243 164 85 Ø243 Ø183 Maintenance • Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and do not use electrical contact cleaner. These may damage the outer packaging and dissolve the parts. 225 ● About This Manual The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device. 225 Tile Rail 608 38 644 32 28 INSTALLING THE SPEAKERS Install the speakers onto the ceiling with the supplied hardware. Pre-installation (Preparation of the Cable) Use stranded wire for cables attached to the Euroblock connector. Strip their insulation as shown in the figure and connect them. About 7 mm (0. 3 in. ) There are two acceptable wiring methods. CAUTION When connecting with low impedance, take note of the combined resistance. Using Loop-Through Terminals For this method, cables are connected from terminals 1 and 4 to the subsequent speaker. If the Euroblock connector is disconnected from a speaker, all subsequent speakers will not work. This can be useful to identify which speaker has a problem. 7 Hold the cable in the strain relief clamp, then tighten screws A and B. When all the Anti-Drop tabs cross over the O-ring, the speaker is held temporarily. You can release your hands from the speaker. NOTE Do not plate stranded wires by solder. Doing so will cause the wire to break. 8 Close the terminal cover and tighten the screw. From amplifier or previous speakers To subsequent speakers To subsequent speakers To release the speaker from the O-ring, press the Anti-Drop tabs. [. . . ] • Do not turn any screws that do not have a guide sleeve in the screw hole. Otherwise, the speaker may fall or malfunction. 3 CONNECT THE WIRING TO THE CONNECTOR AND FIX THE CABLE 1 Pull the wiring from the amplifier through the cut hole. 2 Loosen the screw at the right of the terminal cover to open the terminal cover and remove the Euroblock connector. Speaker 5 SET THE LINE VOLTAGE/IMPEDANCE AND POWER Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/ 70V line distributed system, by rotating the tap selector switch on the front side of the speaker with a flat-blade screwdriver. 4 Plug the connected Euroblock connector into the socket in the speaker. Euroblock connector CAUTION The “X” position should not be selected. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA VXC4




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA VXC4 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.