User manual YAMAHA VX-55B

[. . . ] 12 For Canadian customers To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES003. 13 14 15 IMPORTANT! Please record the serial number of this unit in the space below. Model: Serial No. : The serial number is located on the bottom of the unit. Please read all these instructions regarding your projector and retain them for future reference. [. . . ] Change the setting according to the type of the input video signal. NORMAL Original image size Projects images with an aspect ratio of 4:3 when the input signal is 4:3 image. ZOOM Projects images in the CinemaScope size or Vista size together with subtitles. THROUGH Projects images in their original size as input. 4:3 image (480i, 576i, 480p, 576p, and PC) Available only when the input signal is 480i, 576i, 480p or 576p. 4:3 CinemaScope and Vista image Available only when the input signal is 480i, 576i, 480p or 576p. Squeezed 4:3 (480i, 576i, 480p, 576p) Available only when the input signal is 480i, 576i, 480p or 576p. Not available. 16:9 image (720p) Not available. Bold frames are recommended modes. Changing the settings With the remote control: 1. · Every time the ASPECT button is pressed, the aspect mode changes from DEFAULT to NORMAL, to SQUEEZE, to ZOOM, to THROUGH, and back to DEFAULT. DEFAULT is automatically set to either NORMAL or SQUEEZE depending on the input signal. With the INITIAL menu: (See page 19 for menu setting. ) 1. or TV60 INITIAL MENU POSITION PROGRESSIVE MODE COLOR SYSTEM ASPECT UPPER LEFT AUTO AUTO DEFAULT 3. Select your desired aspect ratio by pressing the button. To cancel the menu: 4. Press the MENU button. 16 Viewing computer images Preparation: · Turn on the power of the connected computer. STANDBY/ON button ON ( I ) button DVI button D-SUB button FOCUS ring ZOOM ring D-SUB/DVI button 1. · If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON button may not work after the power cable is plugged. (The STATUS indicator blinks green. ) After the fan stops rotating, press the STANDBY/ON button to turn back on the POWER indicator. In this condition, the POWER indicator turns red and the STATUS indicator blinks green. Wait about one minute for the STATUS indicator to be off and the POWER indicator to be steadily lit in red. · During this one minute period, the intake fan and exhaust fan rotate to cool the lamp. · Do not unplug the power cable while the STATUS indicator is blinking. Unplugging the power cable immediately after use may cause a breakdown. · The fan may make loud sounds during cooling; this is not a malfunction. STANDBY( )button STANDBY/ON button 18 7 Menu Menu overview Menus are not displayed when no signal is received by the projector. IMAGE CONTRAST BRIGHTNESS WHITE ENHANCE *1 sRGB COLOR TEMP. *1 0 - 60 ± 30 DEFAULT, 0 - 10 ON , OFF CONTRAST R HIGH CONTRAST B MID BRIGHTNESS R LOW BRIGHTNESS B CUSTOM 0 - 20 ± 10 0 - 10 DEFAULT, DYNAMIC, CINEMA1, CINEMA2 0 - 60 0 - 60 ± 30 ± 30 SATURATION *1 *3 *1 *3 HUE *3 SHARPNESS *1 GAMMA SET UP KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN HIDE SCREEN COLOR LAMP MODE LOCATION ± 20 ON , OFF OFF, 5, 10, 15, 30, 60 min ON , OFF BLUE, BLACK BRIGHT, CINEMA FRONT/TABLE, REAR/TABLE, REAR/CEILING, FRONT/CEILING INITIAL MENU POSITION PROGRESSIVE MODE *3 COLOR SYSTEM *3 ASPECT UPPER LEFT, LOWER RIGHT AUTO , VIDEO AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 DEFAULT, NORMAL, SQUEEZE, ZOOM, THROUGH *2 LANGUAGE RESET ALL , ENGLISH, ESPANÕL, DEUTSCH, FRANÇAIS, ITALIANO, EXECUTE SIGNAL HORIZ. POSITION*3 VERT. POSITION *3 *3 PHASE *3 TRACKING *3 D-SUB INPUT *3 SET UP LEVEL SYNC NOISE MASK *3 0 - 999 *2 0 - 999 *2 0 - 31 0 - 9999 *2 RGB, COMPONENT OFF, 3. 5%, 7. 5% ON OFF BEGIN END CLAMP POSITION CLAMP WIDTH LPF *3 0 - 99 0 - 99 0 - 63 1 - 63 ON , OFF A/D SETTING *3 EXECUTE *2 *2 After selecting the items marked with , press the ENTER button. *1: Not available when sRGB is set to ON. *3: Refer to the chart below for availability / unavailability. SATURATION HUE SHARPNESS PROGRESSIVE MODE COLOR SYSTEM HORIZ. POSITION PHASE TRACKING D-SUB INPUT SET UP LEVEL SYNC NOISE MASK A/D SETTING LPF Unavailable when the input source is DVI or the D-SUB source is an RGB signal. Available only when the VIDEO or S-VIDEO source is an NTSC-M or NTSC-4. 43 signal. Available only when the COMPONENT or D-SUB source is a 480i, 480p, 576i or 576p signal. 19 How to set the menus Following describe how to set AUTO POWER OFF time as an example. [. . . ] The protection circuit is working or the lamp is in an abnormal condition. · Wait until the STATUS indicator goes out, then press the STANDBY/ON button. Change with a new lamp if this problem recurs. Steady green Blinking green/red Lamp operation time warning. (Total lamp operation time reached 3000 hours*1 while the power was on. ) Lamp operation time warning. (Total lamp operation time reached 3000 hours*1 while the power was off. ) Lamp operation time warning. [. . . ]