User manual YAMAHA TSX-120

[. . . ] U DESKTOP AUDIO SYSTEM SYSTEME AUDIO DESKTOP TSX-120 OWNER'S MANUAL MODE D'EMPLOI IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 2 3 4 5 6 7 8 9 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 10 11 12 Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. IMPORTANT Please record the serial number of this unit in the space below. [. . . ] The symbol "" with page number(s) indicates the corresponding reference page(s). Notes contain important information about safety and operating instructions. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority. Supplied accessories This product includes the following accessories. Dispose of batteries according to your regional regulations. English 3 En PREPARATIONS BEFORE USING THIS UNIT Turning on/off the system 1 2 Connect the power cable to the wall outlet. Press ON/OFF to turn on the system. Adjusting the clock The clock is not set at the factory. When the system is on: "Hello" appears, then clock and other information are displayed. Example: iPod playback mode display 1 Press CLOCK SET. When the system is off: "Good-bye" appears, then only date and time are displayed. 2 y · This unit has an auto off function, which will automatically switch the system to off if the system is left turned on for 1 hour without playback or any other operation being performed. · Press and hold ON/OFF on the top of the unit for more than 3 seconds to set the system to standby mode. All the information on the front panel display is not displayed in standby mode. · Even in system off/standby mode, the alarm function is available. · The memory back-up circuit prevents stored data such as the time setting from being lost even in system off/standby mode. Select each setting with MENU and confirm with Center. / You can set YEAR MONTH DAY TIME. Notes · This operation can be performed only with the remote control. · Time appears in 12-hour notation (AM/PM), depending on the model. · You can switch 12-hour/24-hour notation by pressing FUNCTION MENU / Center to select TIME FORMAT, then pressing MENU / Center to select 12H/24H. · The time settings are lost after one week when the power cable is disconnected from the wall outlet. 4 En OPERATION USING USEFUL FUNCTIONS Using the alarm functions The unit has the dual alarm function. Each alarm time always appears on the right/left sides of the clock on the front panel display. You can set the different music to the alarm from what you listen to during the setting. OPERATION Note This operation can be performed only with the buttons on the top of the unit. 2 Set the alarm time. 1 While setting the alarm function, the alarm indicator blinks. 3 The > mark on the right side means that you have other menu items on the following screens. You can go to the next menu item setting by pressing ENTER. 3 Setting the alarm time and sound Note To cancel the alarm function setting during the operations, press SETUP1/SETUP2. The alarm is not set. Select and set TYPE BEEP SOURCE VOLUME. 1 Start setting ALARM1/ALARM2. When you want to set the alarm to ALARM1, set on SETUP1, and SETUP2 is for ALARM2. 1 After setting the alarm time, select the alarm type from BEEP/BEEP+MUSIC/MUSIC. ­ BEEP: beep sound only ­ BEEP+MUSIC: beep sound and music selected in an input source, iPod/FM ­ MUSIC: music only If you set TYPE to BEEP+MUSIC, you can play back the desired music in an input source, iPod/ FM and beep sound together at the time you set. The music volume gradually increases to wake you up comfortably, and then the beep sound plays back at the time you set. English 5 En USING USEFUL FUNCTIONS 2 Select the beep sound. [. . . ] Remove the iPod from the unit, then set it in the iPod dock again. 15 En TROUBLESHOOTING You cannot operate from the iPod. "Unknown iPod" appears on the front panel display after you set the iPod. LIST DISP is set to F. PANEL. The iPod you set is not compatible with the playback information display. The iPod being used is not supported by the unit. Set LIST DISP to iPod from the FUNCTION menu ( P. [. . . ]