User manual YAMAHA TF5/TF3/TF1 QUICK GUIDE

[. . . ] To take full advantage of the superior features and performance offered by your TF-series console, and to enjoy years of trouble-free use, please read this document carefully before operating your console. l’avertissement ci-dessus est situé sur l’arrière de l’unité. Explanation of Graphical Symbols Explication des symboles The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. l’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension dangereuse » non isolée à l’intérieur de l’appareil , pouvant être suffisamment élevée pour constituer un risque d’électrocution. [. . . ] € Adjusting SENDS ON FADER for the level sent to AUX for each channel (page 16) • Muting all input channels or effects (page 15) • Turning effects on and off, adjusting the overall level of effects (page 15) Save Your Settings Save your settings You can save your entire mix setup as a Scene. (SCENE window g page 18) If several bands are performing on the same stage, or if a single performer’s mix or audio sources vary greatly from song to song, you can save a complete mix setup for each band or each song as a Scene, and easily switch between Scenes. You can also save individual channel setups by overwriting existing Presets or by saving them as new Presets in the Library screen. After fine-tuning the sound of each channel to suit each instrument or mic, you can save them as Presets and recreate that configuration anytime, easily. ) that A Preset is a file stored in the Library ( contains channel settings such as the type of input (instrument or mic), equalizer and compression settings, etc. The default Presets contain settings for various types of instruments, so you can use them as a starting point when setting up a channel. mUTE Effects on/ off , effects level HINT Using USER DEFINED KEYS What is a "Scene"?A Scene is file that contains all the settings for every channel in your mix. By saving your setups as Scenes, you can load a complete mix in an instant and be ready for any situation. Saving a Scene Recalling a Scene SENDS ON FADER When the console is in the default state, USER DEFINED KEYS (page 15) are configured as "Direct Scene Recall" keys. You can save a Scene by pressing and holding down one of the USER DEFINED KEYS, and recall a Scene by pressing one of the USER DEFINED KEYS. ‘ ⑬ ② ⑪ ③ ⑭ ④ ⑤ ⑥ ⑦ ⑧ 1 Channel Strip section (page 14) 2 ST IN (stereo input) section (page 14) 3 FX (effects) section (page 15) 4 USER DEFINED KEYS section (page 15) ⑩ 5 MUTE section (page 15) 6 METER section (page 15) 7 PHONES section (page 15) 8 FADER BANK section (page 16) 9 TAP key (page 16) ⑨ 0 SENDS ON FADER section (page 16) a Display section (page 16) b STEREO/MASTER section (page 20) ⑫ TF series Quick Guide c iPad connector (page 20) d USB connector (page 20) - 10 - Panels 4-2 Rear panel ① ② ③ ⑩ ⑨ ⑧ ⑦ ⑥ ⑤ ④ 8 Ventilation holes To prevent overheating, do not block the ventilation holes. 9 Power switch When the switch is in the When the switch is in the position, the power is on. These jacks are used mainly to output AUX channels and STEREO channels. 2 ST IN jacks Stereo input jacks that can be used for connecting a CD player or other line level device. 3 INPUT jacks Combination jacks that support both XLR and TRS phone connectors. 4 NETWORK connector RJ-45 jack used to connect the console to a computer via an Ethernet cable (CAT5e or higher recommended). This connector is used mainly to control mix parameters or to edit Scene memories and Libraries from the dedicated "TF Editor" program or the iPad app. 5 USB TO HOST connector USB connector used to connect the console to a computer, allowing the console to function as an audio interface. When using with a computer running Microsoft Windows, the Yamaha Steinberg USB Driver is required. You can use the connected foot switch as an effect bypass switch, a mute switch, or use it to tap the delay time. When connecting to a power outlet, first connect the power cord to the console, then connect the power cord to the power outlet. [. . . ] While this indicator is displayed, do not turn off the unit or disconnect the USB memory drive. The unit, the drive, and data stored on the drive could become damaged. ⑥ 6-13 iPad connector Allows you to connect an iOS device or a USB storage device. To connect an iOS device, use the dedicated cable that was included with the device. [. . . ]