User manual YAMAHA TF STAGEMIX

[. . . ] TF5 / TF3 / TF1 DIGITAL MIXING CONSOLE TF StageMix User's Guide EN Note • The software and this document are the exclusive copyrights of Yamaha Corporation. • Copying or modifying the software or reproduction of this document, by any means, whether in whole or in part, is expressly forbidden without the written consent of Yamaha Corporation. • Yamaha Corporation makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of the software and this document. • Copying of commercially available music sequence data and/or digital audio files is strictly prohibited except for your personal use. [. . . ] The CUE button is not displayed for the MONITOR channel. CH Name area Allows you to adjust the channel's pan/balance, and displays the channel's number, name, icon, and color. 1 Pan/balance slider Drag left and right to adjust the pan or balance of the channel. The control stops at the center position; you can then continue to drag it left or right as desired. When the pan or balance is set to the center position, a round icon is displayed. You can also double-tap this area to set the pan or balance to the center position. You can adjust pan/balance for multiple channels at the same time. 2 Channel display Displays the channel number, name, icon, and color. Overview strip area The STEREO channel strip is normally displayed in the overview strip area. When using SENDS ON FADER mode, the destination AUX channel or SUB channel strip is displayed here. You can switch to SENDS ON FADER mode by tapping a channel number displayed on the left side of the strip. If you enter SENDS ON FADER mode while an FX channel is selected, nothing is displayed here. - 16 - TF StageMix User's Guide Screen areas SENDS ON FADER screen Allows you to use the faders to adjust the send level for each channel. In SENDS ON FADER mode, the details area changes to display SENDS ON FADER information. Note, however, that the display does not change for channels that have no send destination. 1 Send pan slider Displayed for stereo AUX buses. Allows you to adjust the pan of the signal sent to the AUX bus. 2 Send ON button Determines whether a signal is sent (on) or not sent (off) to the corresponding AUX bus. This button lights when the send is turned on. 3 Send level fader Allows you to adjust the send level of the corresponding channel. You can tap the value and then increase and decrease it by tapping the up and down arrows. 4 Fader Determines the amount of signal sent to the corresponding AUX bus. 5 PRE button Allows you to select whether the pre-fader or post-fader signal is sent to the corresponding AUX bus. On: Before the fader Off: After the fader 6 CH NAME display Displays the channel's number, name, icon, and color. - 17 - TF StageMix User's Guide Screen areas TOOLBAR area Displays information about the current scene and allows you to switch between the different details screens. Scene area Tool buttons Menu button Scene area Displays the name of the selected scene. If you adjust parameters after recalling a scene, an "E" is displayed. If you select a scene that is write-protected, a lock icon is displayed. If you select a scene that is different from the current scene and do not recall it, the scene number begins flashing. Tool buttons Tap a button to change the content displayed in the details area. See "Processing area" (page 15) for more information. Menu button Tap to display the context menu that corresponds to the current screen. For details about the content menu, refer to the explanations for the corresponding screens. HOME screen menu The following items are available in the HOME screen's context menu. CH Paste: Pastes settings from the copied channel and applies them to the selected channel. CH Default: Resets the settings of the current channel to their default values. Clear CUE: Turns off all cue selections. - 18 - TF StageMix User's Guide Screen areas SCENE screen Allows you to manage previously saved mixer setups, or "Scenes". 1 Scene list selection button Allows you to switch between the available Scene lists. SCENE B: Displays the Scenes stored in Scene list B. 2 Scene list Displays the Scenes saved in the selected Scene list. [. . . ] Swipe left or right on an empty area to display the gain sliders for other bands. 5 Output level meter Displays the GEQ output level. 6 Available bands display Displays the number of additional bands that you can adjust. GEQ screen menu The following items are available in the GEQ screen's context menu. Copy: Copies the GEQ parameters of the selected channel to the clipboard. Paste: Pastes the GEQ parameters in the clipboard to the selected channel. Compare: Allows you to compare the GEQ parameters of the selected channel with the GEQ parameters in the clipboard by switching between the two. [. . . ]