User manual YAMAHA STAGEPAS300

[. . . ] EN Owner's Manual Introduction Thank you and congratulations on your purchase of the Yamaha PORTABLE PA SYSTEM STAGEPAS 300. The STAGEPAS 300 is a versatile, compact PA system consisting of two speakers and a mixer. In order to get the most out of your new STAGEPAS 300 and its sophisticated functions, we suggest you read through this manual thoroughly. Also keep it in a safe place for future reference. Package Contents Two speakers, mixer, panel, power cord, two speaker cables, Owner's Manual (this booklet) NOTE: The mixer and the panel are installed in the speakers when the STAGEPAS 300 leaves the factory. Dimensions Troubleshooting Power does not turn on Is the included power cord correctly connected to a power outlet? Speaker Mixer MSC 1 2 3 160 MSC 1 455. 5 2 3 MSC 1 Before turning on the mixer Remove the mixer 1. Be sure that the mixer's power switch is turned off. Power shuts down suddenly Is the vent on the top panel of the mixer blocked? [. . . ] The MONITOR OUT jack outputs the signal prior to routing through the MASTER LEVEL control. Adjust the level of output signal from the MONITOR OUT jack with the MONITOR OUT control. If the signals are output from the L (left) MONITOR OUT jack, the mixer feeds the mixed L and R signals to the jack. SPAIN/PORTUGAL Yamaha-Hazen Música, S. A. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: BRAZIL Yamaha Musical do Brasil Ltda. Brasil Tel: 011-3085-1377 Turning the power on/ off Caution SWEDEN Yamaha Scandinavia AB J. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 SINGAPORE Yamaha Music Asia Pte. , Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 ARGENTINA Yamaha Music Latin America, S. A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 Power supply/Power cord · Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. · When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Handling caution · When turning on the AC power in your audio system, always turn on the device LAST, to avoid speaker damage. When turning the power off, the device should be turned off FIRST for the same reason. · Do not insert your fingers or hands in any gaps or openings on the device (vents, , ports, etc. ). · Avoid inserting or dropping foreign objects (paper, plastic, metal, etc. ) into any gaps or openings on the device (vents, ports, etc. ) If this happens, turn off the power immediately and unplug the power cord from the AC outlet. · Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. Prolonged use in this condition could cause overheating and result in fire. · Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-). Interference From Cell Phones Using a cell phone near the speaker system can induce noise. If this occurs, move the cell phone further away from the speaker system. [. . . ] PART/ZONE NUMBER 12 13 14 15 16 MUTE EDIT JOB STORE F1 F2 F3 F4 F5 F6 EXIT ENTER 9 10 11 COMPARE OCTAVE DOWN UP SCENE STORE SET LOCATE EXECUTE SOLO MASTER VOLUME CS 1 CS 2 CS 3 CS 4 ZONE 1 ZONE 2 ZONE 3 ZONE 4 For each channel you want to apply reverb, set the corresponding REVERB switch to ON ( ). R L This position CD Player Depending on the device used, set the MIC/LINE switch to MIC ( ) or LINE ( ) as appropriate. For low-level signals (such as that of microphones), set the switch to the MIC ( ) position. For high-level signals (such as keyboard instruments and audio equipment), set the switch to the LINE ( ) position. While playing your instrument or singing into the microphone, adjust the LEVEL control of the corresponding channel. Adjust the LEVEL Control of the corresponding channel so that the "0" LED lights up momentarily. R Powered SP L L R Use the REVERB control to adjust the overall reverb. R L L L R R L Controls and Functions AC IN jack Connect the included power cable here. Be sure to use the included power cord. Use of other cords may result in malfunction, heat generation, or fire. Caution SPEAKER L/R jacks (for included speakers only) These output the mixed signal channels from 1 to 7/8, and the level is adjusted with the MASTER LEVEL control. Connect only the included speakers. Channel input jacks (CH 1 to 4) For connecting a guitar, microphone, keyboard or other instrument/device. [. . . ]