User manual YAMAHA S4115H

[. . . ] NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. [. . . ] If the Disklavier is not going to be used for a long period, set the MAINS switch to OFF. When the Disklavier is turned off, wait at least 5 seconds before turning it on again. Note: The MAINS switch only needs to be switched off when you are not going to use the Disklavier for a long period of time. For daily use, only the [STANDBY / ON] button on the Control Unit needs to be turned on and off. 2 Press [STANDBY / ON] on the front panel of the Control Unit. DRIVE SELECT CONTRO L UNI T DKC 55RCD PLAY/P GENER AUSE AL INSTRUMENT STOP REC SONG SELECT /REV ¥ FWD STANDB Y ON ENTER L PART R VOICE FUN The following message appears on the display. Your Disklavier is now ready for use. 14 Setting the Internal Calendar The Disklavier has an internal calendar that can be set from 1/1/1985 00:00:00 to 12/31/2084 23:59:59. Set the calendar accurately so that the Disklavier displays the correct current time during Stop mode. Setting the correct time is also important for engaging timer-controlled programs (see Chapter 3 "Timer Play" in the Advanced Operation Manual for details). Time is displayed in 24-hour format. A display similar to the following appears, with the clock stopped and the hours display flashing. Flashes English 4 Use [<] and [>] to select year, month, date, hours, minutes, and seconds, and use the [­/NO] and [+/YES] buttons to set a value. ­/NO +/YES Chapter 4: Turning On/Off Your Disklavier 1 Hold down [FUNC. ] and press [STANDBY / ON]. FUNC. + STANDBY ON Pressing both [­/NO] and [+/YES] simultaneously in each respective field sets the year to 1990, month and day to 1, and the hours, minutes, and seconds to 0. The setup menu appears. 5 Press [ENTER]. ENTER The date and time are stored in the internal calendar, and the display returns to the current time display. 2 Press [>] until the c cursor is next to the Clock Adjust option, then press [ENTER]. ENTER Calendar Memory The date and time that you set are saved in the calendar memory when you turn off the Control Unit. The calendar memory can maintain the correct date and time for about a month. If you do not use the Control Unit for over a month, you must reset the calendar following the above procedure. Note: The internal calendar is equipped with a storage battery (capacitor) that does not need to be replaced or recharged. However, the Control Unit must be turned on for at least 10 minutes a month in order to maintain power. A display similar to the following appears, showing the current date and time. 3 Press [ENTER]. ENTER 15 Chapter 5 Display (LCD) and DRIVE Indicator Various information is shown in the display (LCD: Liquid Crystal Display) and DRIVE indicator on the Control Unit. This chapter describes some of the frequently displayed indications. DRIVE Indicator The DRIVE indicator lets you know which disk is selected. Pressing the [SELECT] buttons toggles the indication as follows: (Fd) (Cd) F E d C b A 9 8 7 0 1 SELECT Disk Title When you select a floppy disk or Memory Disk for playback, the title of the selected disk scrolls across the display. Note: CDs have no disk title. 2 3 4 5 6 Song Title The title of a song appears during song playback. Time Display When the Disklavier is not playing, the current time is displayed in hours and minutes. The time display starts counting up and the velocity meters show the velocity of the piano part notes currently being played, as shown. 2 Press [PLAY/PAUSE] again to continue playback. PLAY/PAUSE Chapter 6: Basic Playback Stopping Playback Press [STOP]. STOP Playback stops and the song returns to the beginning. Pressing [STOP] while in Pause mode cancels Pause mode. 21 Selecting Songs with the Control Unit Press [SONG SELECT the next song. Press [SONG SELECT the previous song. SONG SELECT/REV FWD Selecting Songs with the Remote Control You can also select songs at any time using the [SONG SELECT] buttons or number pad on the remote control. ] to select ] to select Using the [SONG SELECT] Buttons Press [SONG SELECT the previous song. Press [SONG SELECT the next song. SONG SELECT To select other songs on the disk, press and hold down [SONG SELECT ] or [SONG SELECT ] until the number of the desired song appears. If the current song is the first song on the disk, pressing [SONG SELECT ] causes the disk title to scroll across the display. To stop the title scrolling, press [STOP]. ] to select ] to select Remote Control Using the Number Pad 1 To select a song from 1 to 9, press the corresponding number button. SEARCH 1 4 7 2 5 3 DRIVE 6 9 0 Remote Control To select song number 5 for example, simply press [5]. 22 2 To select a song numbered 10 and above, enter the first digit, then within 2 seconds, enter the second digit. SEARCH Fast Preview & Review During playback, Fast Preview and Review allow you to quickly search through a song while listening to the sound. This is useful for locating a desired position within a song. Note: No sound is produced by the piano when fastpreviewing or reviewing PianoSoft. PlusAudio CDs. 1 2 5 3 DRIVE 6 9 0 English 7 8 Remote Control 1 SEARCH To preview, press [SONG SELECT ]. SONG SELECT/REV¥FWD Chapter 6: Basic Playback 1 4 7 2 3 DRIVE REV·FWD 6 Remote Control 8 9 0 Remote Control To select song number 12 for example, press [1], then [2]. If a song number higher than that of the last song on the disk is entered, the last song on the disk is selected. To review, press [SONG SELECT ]. SONG SELECT/REV·FWD REV·FWD Remote Control 2 Press [PLAY/PAUSE] to continue normal playback. Press [STOP] to engage Pause mode. If a song is reviewed all the way to the beginning, Pause mode is engaged. Pressing [PLAY/PAUSE] starts playback of the next song. 23 Fast Forward & Reverse In Pause mode, fast forward and reverse allow you to quickly locate a desired position in a song. Fast Forward and Reverse search faster than preview and review and the piano does not play. [. . . ] A change of +1 decreases the speed of the MIDI (piano) part by approximately 13ms. Upon completion of the adjustments: 3 Press [ENTER]. To delete the adjustment value, press [+/YES]; to cancel the deletion, press [­/NO]. 4 7 Align the cursor with QUIT, and press the [ENTER] button. After the SPS adjustment value has been deleted, the "SPS Adjust" screen is restored. The status changes to "MEASURING. " The cursor returns to "SPS Adjust. " (Additional checkpoints for function) Operations on the SPS Adjust screen can be performed only in the stop status. When factory reset is performed, all the SPS adjustment values will be deleted. 8 To register the adjustment value, press [+/YES]; to cancel the registration, press [­/NO]. 64 PianoSmart Recording During recording, songs can be recorded as MIDI data while a CD is being played back. You can record your song onto Memory Disks or a floppy disk. 3 Press [SONG SELECT] to select the song on the CD that is to be recorded. 4 Press [REC] to engage the Record Standby mode. English When Recording a New Song 1a Specify a disk. Use the disk in SMF format. Note: If you are recording to a floppy disk, make sure that the disk's erasure protection tab is set to "unprotected". [. . . ]