User manual YAMAHA S03

[. . . ] OWNER'S MANUAL SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. [. . . ] Init (Initialize) You can reset (initialize) all parameters of a Multi to their default settings. You can also selectively initialize certain parameters, such as Common settings, settings for each Part, and so on. Note that this does not return the Multi to its original state prior to editing. Instead, it is useful when building a completely new Multi from scratch. Multi Mode 3. CpyCtl (Copy Controller) This let you copy the Controller settings for the Voice assigned to the Part. CpyCtl PAGE PART ELEM KEY 3 OCTAVE P 1 Settings: 1 ~ 16, A (All Parts) PAGE PART ELEM KEY 1 OCTAVE Init multi I Select Parameter Type to be Initialized Use the [DEC/NO] and [INC/YES] buttons to select the parameter to be initialized. When this is set to "Part, " use the [+]/[­] buttons to select the desired Part (1 - 16). Settings: multi (Current Multi), cmmn (Current Common), part (Current Part 1 ~ 16) n The following parameters can be copied. · MW Filter Control · MW Pitch Modulation Depth · MW Filter Modulation Depth · MW Amplitude Modulation Depth · Pitch Bend Range · AC1 Filter Control · AC1 Filter Modulation Depth · AC1 Amplitude Modulation Depth · Portamento Switch · Portamento Time 4. CpyPart (Copy Part) This lets you copy Part parameter settings of the Multi being edited to another Part in the same Part. Use the [­] and [+] buttons to select the desired destination Part (1 - 16). 2. CpyVar (Copy Variation Effect) When Var Connect is set to "SYS, " this lets you copy the Effect settings for the Voice assigned to the Current Part. When Var Connect is set to "INS, " this lets you copy the Variation Effect settings for the Voice assigned to the Part for which "Var Send" (PAGE 24 in Multi Part Edit) was set to "on. " If all of the Parts' Var Send settings are "off, " the Part having the Voice Effect settings to be copied can be selected, just as above (when Var Connect is set to "SYS"). PAGE PART ELEM KEY 4 OCTAVE CpyPart P P 102 source Part desired destination Part (1 - 16) Settings: P1 ~ P16 (Part 1 ~ 16) Var Connect=SYS Var Connect=INS 5. BlkDmp (Bulk Dump) You can send all the parameter settings for the current Multi or all Multis to your computer or some other external MIDI device using Bulk Dump. CpyVar PAGE PART ELEM KEY PAGE CpyVar PART ELEM KEY 2 OCTAVE P 1 2 OCTAVE Settings: P1 ~ P16 (Part 1 ~ 16) (When Var Connect is set to "SYS, " or when Var Connect is set to "INS" and all Parts' Var Send settings are "off. ") No Parameter (When Var Connect is set to "INS" and one Part's Var Send settings is "on. ") n The following parameters can be copied. · Variation Effect Type · Variation Parameters · MW Variation Control Depth · AC1 Variation Control Depth n When you copy the Variation effect data of a Drum Voice, the 2 Band EQ effect settings are copied. PAGE PART ELEM KEY 5 OCTAVE BlkDmp Curnt Settings: Curnt (Current Multi), All (All Multis), Systm (All Utility and MIDI data) n To send Voice data, refer to the corresponding Bulk Dump function in the Voice Jobs (page 88). n In order to perform a Bulk Dump, the appropriate MIDI Device Number must be set. n For an application example showing how to use the Bulk Dump function, see page 42. 68 Multi Store You can store (save) your original parameter settings for up to 32 Multis to User Memory. The procedure is as follows. n When you perform this, the settings for the destination Multi will be overwritten. Important data should always be backed up to computer, Yamaha MIDI Data Filer MDF3 or some other storage device. Multi Mode 1Press the [STORE] button after editing a Multi. The Multi Store screen appears. Store MLT01 PAGE PART ELEM KEY OCTAVE 2Use [DEC/NO] and [INC/YES] buttons to select the destination Multi Number. 3When you press the [ENTER] button, you will be prompted for confirmation. Store Sure? PAGE PART ELEM KEY OCTAVE 4Press the [INC/YES] button to confirm. The message "Excuting. . " will be displayed while the Job is being processed. When it has been completed, a "Completed" message appears, and operation returns to the Multi Play mode. n You can press the [DEC/NO] button to cancel the Job. This will return you to the original screen. 69 Voice Mode Voice Edit There are two types of Voices: Normal Voices and Drum Voices. [. . . ] Tel: 971-4-881-5868 HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: 053-460-2445 SY22 FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. [. . . ]