User manual YAMAHA RX-V863

[. . . ] U RX-V863 AV Receiver OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11 · Explanation of Graphical Symbols 12 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 13 1 2 3 4 5 6 7 8 9 Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] See page 97 for details. Note The Yamaha Bluetooth adapter can be paired with up to eight Bluetooth components. When pairing is conducted successfully with a ninth component and the pairing data is registered, the pairing data for the least recently used other component is cleared. Quick pairing To ensure security, a time limit of 8 minutes is set for the pairing operation. You are recommended to read and fully understand all the instructions before starting. Playback of the BluetoothTM component 1 Rotate the RINPUT selector (or set the operation mode selector to FSOURCE and then press 4V-AUX) to select "V-AUX" as the input source. When the connected Bluetooth adapter detects the Bluetooth component, "BT connected" and the DOCK indicator appears in the front panel display. 1 Rotate the RINPUT selector (or set the operation mode selector to FSOURCE and then press 4V-AUX) to select "V-AUX" as the input source. Once the Bluetooth adapter starts pairing, "Searching. . . " appears for a moment. While the Bluetooth adapter is in the pairing mode, DOCK indicator flashes in the front panel display. y To cancel the pairing, press CBAND (or 7BAND) again. 2 3 2 y · When you press 8ENTER on the remote control, the connected Bluetooth adapter searches and connect to the last connected Bluetooth component. If the Bluetooth adapter cannot find the Bluetooth component, "Not found" appears in the front panel display. · To disconnect the Bluetooth adapter from the Bluetooth component, press 9RETURN. 72 En RECORDING Recording Recording adjustments and other operations are performed from the recording components. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources encoded in DTS, the following considerations and adjustments need to be made. To play DTS-encoded DVDs and CDs (when using a digital audio connection) on your DTS-compatible player, follow its operating instructions to make a setting so that the analog signal will be output from the player. Notes · When this unit is set to the standby mode, you cannot record between other components connected to this unit. · TONE CONTROL (see page 52) and VOLUME settings, the speaker level (see page 52) and the sound field programs (see page 48) do not affect recorded material. · The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded. · The XM Satellite Radio and SIRIUS Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks. · HD Radio signals can be output at the analog AUDIO OUT (REC) jacks and DIGITAL OUTPUT jack for recording. · Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Likewise, analog signals input at the AUDIO IN jacks are not output at the DIGITAL OUTPUT jack. Therefore, if your source component is connected to provide only digital or analog signals, you can only record digital or analog signals. · A given input source is not output on the same AUDIO OUT (REC) channel. · S-video and composite video signals pass independently through the video circuits of this unit. [. . . ] 26 132 En Index VIDEO CONV. , Video settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Video conversion, Video settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 W W-1:OUT OF PHASE, Automatic setup warning message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 W-2:OVER 24m (80ft), Automatic setup warning message . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]