User manual YAMAHA RX-V800RDS

[. . . ] GB RX-V800RDS Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. 2 Install this unit in a well ventilated, cool, dry, clean place with at least 30 cm on the top, 20 cm on the right and left, and 10 cm at the back of this unit -- away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid. [. . . ] · We recommend that you adjust the items on the SET MENU while using a video monitor. It is easier to see the video monitor than it is to see the front panel display on this unit while adjusting the items. 1 3, 6 4, 5 2 PREPARATION Note · The indication on the front panel display is the abbreviation of the OSD. 1 SPEAKER SET 1A CENTER SP BASIC OPERAIONT 1B MAIN SP 1C REAR L/R SP 1D LFE/BASS OUT 1E MAIN LEVEL 2 3 4 5 6 7 8 9 LOW FRQ TEST L/R BALANCE HP TONE CTRL CENTER GEQ INPUT RENAME I/O ASSIGNMENT INPUT MODE PARAM. INI Note · Some items require extra steps to change to the desired setting. 1 2 Set the selector dial to the AMP/TUN (or DSP/TUN) position. Press SET MENU to enter the SET MENU. SET MENU 1/4 1 SPEAKER SET 2 LOW FRQ TEST 3 L/R BALANCE 4 HP TONE CTRL / :Up/Down ­/+ Enter ADVANCED OPERATION 3 Press u/d repeatedly to select the item (1 to 15) you want to adjust. ADDITIONAL INFORMATION 10 DOLBY D. SET 10A LFE LEVEL 10B D-RANGE 11 DTS LFE LEVEL 12 6. 1/ES AUTO 13 SP DELAY TIME 14 DISPLAY SET 15 MEMORY GUARD SET MENU 1/4 1 SPEAKER SET 2 LOW FRQ TEST 3 L/R BALANCE 4 HP TONE CTRL / :Up/Down ­/+ Enter y · By pressing SET MENU repeatedly, you can select items in the same order as when pressing d. APPENDIX 4 Press j or i once to enter the setup mode of the selected item. The last setting you adjusted appears on the video monitor or on the front panel display. 2 LOW FRQ TEST TEST TONE · · · · · OFF OUTPUT · · · MAIN L/R FRQ · · · · · · · · · · 88Hz English 39 SET MENU Depending on the item, press u/d to select a sub item. 2 LOW FRQ TEST TEST TONE · · · · · OFF OUTPUT · · · MAIN L/R FRQ · · · · · · · · · 88Hz 1 SPEAKER SET (speaker mode settings) Use this feature to select suitable output modes for your speaker configuration. You must set the output mode when you use a subwoofer. Notes 5 Press j / i repeatedly to change the setting of the item. 2 LOW FRQ TEST TEST TONE · · · · · ·ON OUTPUT · · · MAIN L/R FRQ · · · · · · · · · 88Hz · When 96-kHz sampling digital signals are input to this unit, level adjustments in items 1B and 1D are possible, but those in items 1A, 1C and 1E are not affected. · When 6CH INPUT is selected as the input source, level adjustments in items 1A through 1E are not affected. I 1A CENTER SP (center speaker mode) By adding a center speaker to your speaker configuration, the unit can provide good dialog localization for many listeners and superior synchronization of sound and images. The OSD shows a large, small or no center speaker depending on how you set this item. Choices: LRG (large), SML (small), NONE Initial setting: LRG LRG Select this if you have a large center speaker. The entire range of the center channel signal is directed to the center speaker. 6 Press u/d repeatedly until the current DSP program appears or simply press one of the DSP program group button to exit from the SET MENU. or 1A CENTER SP Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the settings of the SET MENU you adjusted will return to the factory settings. If so, adjust the items again. LRG SML NONE SML Select this if you have a small center speaker. The lowfrequency signals (90 Hz and below) of the center channel are directed to the speakers selected with "1D LFE/BASS OUT". 1A CENTER SP LRG SML NONE 40 SET MENU NONE Select this if you do not have a center speaker. All of the center channel signals are directed to the left and right main speakers. I 1C REAR L/R SP (rear speaker mode) The OSD shows large, small or no rear speakers depending on how you set this item. Choices: LRG (large), SML (small), NONE Initial setting: LRG LRG Select this if you have large left and right rear speakers or if a rear subwoofer is connected to the rear speakers. The entire range of the rear channel signal is directed to the left and right rear speakers. INTRODUCTION 1A CENTER SP LRG SML NONE I 1B MAIN SP (main speaker mode) The OSD shows large or small main speakers depending on how you set this item. Choices: LARGE, SMALL Initial setting: LARGE LARGE Select this if you have large main speakers. The entire range of the left and right main channel signal is directed to the left and right main speakers. PREPARATION 1C REAR L/R SP LRG SML NONE 1B MAIN SP SML Select this if you have small left and right rear speakers. The low-frequency signals (90 Hz and below) of the rear channel are directed to the speakers selected with "1D LFE/BASS OUT". BASIC OPERATION 1C REAR L/R SP LARGE SMALL ADVANCED OPERATION SMALL Select this if you have small main speakers. The lowfrequency signals (90 Hz and below) of the main channel are directed to the speakers selected with "1D LFE/BASS OUT". LRG SML NONE NONE Select this if you do not have rear speakers. 1B MAIN SP 1C REAR L/R SP ADDITIONAL INFORMATION LARGE SMALL LRG SML NONE y Note · When you select MAIN for "1D LFE/BASS OUT", the lowfrequency signals (90 Hz and below) of the main channel are directed to the main speakers even if you select SMALL for the main speaker mode. · This unit is set in the virtual CINEMA DSP mode by selecting NONE for "1C REAR L/R SP". APPENDIX English 41 SET MENU I 1D LFE/BASS OUT (bass out mode) LFE signals carry low-frequency effects when this unit decodes a Dolby Digital or DTS signal. [. . . ] 15 kg (33 lbs) BASIC OPERAIONT ADVANCED OPERATION · Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]