User manual YAMAHA RX-V661

[. . . ] G RX-V661 AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. 2 Install this sound system in a well ventilated, cool, dry, clean place ­ away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. [. . . ] Check that the colon (:) appears in the front panel display. Flashes MEMORY A :FM 89. 10MHz Preset station group Colon (:) English 51 En FM/AM tuning 4 Press 5 PRESET/TUNING l / h to select a preset station number (1 to 8) while the MEMORY indicator is flashing. · Press 5 l to select a lower preset station number. Flashes 2 Press 5 PRESET/TUNING l / h on the front panel (or D PRESET/CH k / n on the remote control) to select the desired preset station number (1 to 8). The preset station group and number appear in the front panel display along with the station band and frequency. MEMORY A1:FM 89. 10MHz Preset station number A1:FM 89. 10MHz Exchanging preset stations You can exchange the assignments of two preset stations with each other. The example below describes the procedure to exchange preset station "E1" with "A5". 5 Press 6 MEMORY while the MEMORY indicator is flashing. The station band and frequency appear in the front panel display with the preset station group and number you have selected. The MEMORY indicator disappears from the front panel display. 1 Select preset station "E1" using 4 A/B/C/D/E and 5 PRESET/TUNING l / h on the front panel. "E1" and the MEMORY indicator flash in the front panel display. Flashes A1:FM 89. 10MHz The displayed station has been stored as A1. 2 Notes · Any stored station data existing under a preset station number is cleared when you store a new station under the same preset station number. · The reception mode (stereo or monaural) is stored along with the station frequency. MEMORY E1:FM 89. 10MHz Flashes Selecting preset stations You can tune into any desired station simply by selecting the preset station group and number under which it was stored. y When performing this operation with the remote control, set the operation mode selector to L SOURCE and then press TUNER to select "TUNER" as the input source. 3 Select preset station "A5" using 4 A/B/C/D/ E and 5 PRESET/TUNING l / h. "A5" and the MEMORY indicator flash in the front panel display. See "Selecting preset stations" on the left column. Flashes MEMORY 1 Press 4 A/B/C/D/E (or press D A/B/C/D/E l / h) to select the desired preset station group (A to E). The preset station group letter appears in the front panel display and changes each time you press the button. A5:FM 89. 10MHz Flashes 4 Press 2 EDIT again. "EDIT E1­A5" appears in the front panel display and the assignments of the two preset stations are exchanged. 52 En RADIO DATA SYSTEM TUNING (EUROPE MODEL ONLY) Radio Data System tuning (Europe model only) Radio Data System is a data transmission system used by FM stations in many countries. This unit can receive various Radio Data System data such as PS (program service), PTY (program type), RT (radio text), CT (clock time), and EON (enhanced other networks) when receiving Radio Data System broadcasting stations. Displaying the Radio Data System information Use this feature to display the 4 types of the Radio Data System information: PS (program service), PTY (program type), RT (radio text) and CT (clock time). Notes · You can select one of the Radio Data System display modes only when the corresponding Radio Data System indicator lights up in the front panel display. It may take a while for this unit to receive all of the Radio Data System data from the station. · You can select only the available Radio Data System display modes being offered by the station. · If the signals being received are not strong enough, this unit may not be able to utilize the Radio Data System data. In particular, the "RT" mode requires a large amount of data and may not be available even when the other Radio Data System display modes are available. · In case of poor reception conditions, press 7 TUNING AUTO/ MAN'L on the front panel so that the AUTO indicator disappears from the front panel display. · If the signal strength is weakened by external interference while this unit is receiving the Radio Data System data, the reception may be cut off unexpectedly and ". . . WAIT" appears in the front panel display. · When the "RT" mode is selected, this unit can display the program information by a maximum of 64 alphanumeric characters, including the umlaut symbol. [. . . ] Speaker Impedance level If you use one set (A or B), the impedance of each speaker must be 8 or higher. Front If you use two sets (A and B), the impedance of each speaker must be 16 or higher. * Center Surround Surround back If you use one set (A or B), the impedance of each speaker must be 4 or higher. Front If you use two sets (A and B), the impedance of each speaker must be 8 or higher. Center Surround Surround back * 1 2 Set the operation mode selector to L AMP or L SOURCE. [. . . ]