User manual YAMAHA RX-V595ARDS

[. . . ] BG RX-V595aRDS Natural Sound AV Receiver Ampli-Tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTE ZUBEHÖRTEILE MEDFÖLJANDE TILLBEHÖR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES · After unpacking, check that the following parts are included. · Après le déballage, vérifier que les pièces suivantes sont incluses. · Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. · Kontrollera efter uppackningen att följande delar finns med. [. . . ] · For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure for more than one week, the memory will be erased. If so, it can be re-stored by simply following the preset tuning procedure. or 2 Select the preset station number. Front panel Remote control or 30 English AUTOMATIC PRESET TUNING (for RDS stations only) You can also make use of the automatic preset tuning function for RDS stations only. This function enables the unit to perform automatic tuning and to sequentially store RDS stations with strong signals. Up to 40 stations can be stored automatically in the same way as that for manual preset tuning on page 29. * See pages 33 to 35 for details on RDS stations. 31 To store stations 24 4 To tune in to higher frequencies, press the UP side of TUNING once. To tune in to lower frequencies, press the DOWN side of TUNING once. Front panel 1 Select the FM band. Front panel 2 Press TUNING MODE so that the "AUTO TUNING" indicator lights up on the display. Front panel * If TUNING is not pressed, automatic preset tuning soon begins automatically toward the higher frequencies. Automatic preset tuning begins from the frequency currently displayed. * If more than 8 stations are received, they are stored as preset station numbers in other groups (B, C, D and E) in that order. Lights up 3 Press MEMORY and hold for about three seconds. Front panel Flashes If you want to store the first station received by automatic preset tuning as a desired preset station number For example, if you want to store the first received station as C5, select "C5" while "A1", the "MEMORY" indicator and the "AUTO TUNING" indicator flash after pressing MEMORY in step 3. The first received station is stored as C5, and the next stations as sequentially C6, C7 . . . If stations have all been stored up to E8, automatic preset tuning stops automatically. When automatic preset tuning is completed The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure in the section "To recall a preset station" on page 30. 31 Notes · You can manually replace a preset station with another FM or AM station by simply following the procedure in the section "To store stations" on page 29. · An automatic preset tuning search will be performed through all RDS network frequencies until stations have been stored up to E8. Even if the number of received stations is not enough to be stored up to E8, the search is automatically ended after searching all frequencies. · With this function, only RDS stations with sufficient signal strength are automatically stored. If the station you want to store is weak in signal strength, tune in to it manually in monaural sound and store it by following the procedure in the section "To store stations" on page 29. * There may be a case that this function cannot receive a station which could be received by the automatic tuning method. This is because this function receives a large volume of PI (Program Identification) data along with the station. EXCHANGING PRESET STATIONS You can exchange the assignment of two preset stations with each other as shown below. 2, 4 Example If you want to change the preset station from "E1" to "A5", or vice versa. 1 2 Recall preset station "E1" by following the procedure in the section "To recall a preset station" on page 30. 3 Next, recall preset station "A5" by following the same procedure as that in step 1. Press EDIT. Front Panel Flashes Flashes 4 Press EDIT once more. Front Panel Shows the exchange of stations has been completed. 32 English RECEIVING RDS STATIONS Radio Data System (RDS) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal. RDS data contains various information such as PI (Program Identification), PS (Program Service name), PTY (Program Type), RT (Radio Text), CT (Clock Time), EON (Enhanced Other Networks), etc. The RDS function is used by network stations. DESCRIPTION OF RDS DATA This unit can receive PI, PS, PTY, RT, CT, and EON data when receiving RDS broadcast stations. PS (Program Service name) mode: The name of the RDS station being received is displayed. RT (Radio Text) mode: Information about the program (such as the title of a song, name of the singer, etc. ) on the RDS station being received is displayed by a maximum of 64 alphanumeric characters, including the umlaut sign. [. . . ] 3. 5 kHz Filter Characteristics MAIN L/R, REAR L/R (SPEAKER: SMALL) (H. P. F) . . . . . . . . . . . . . . . . . . . . . ±300 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB Signal-to-Noise Ratio (DIN-Weighted, 40 kHz Dev. ) Mono/Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 dB/69 dB Harmonic Distortion (1 kHz) Mono/Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]