User manual YAMAHA RX-V520RDS

[. . . ] GB RX-V520RDS Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Install this unit in a well ventilated, cool, dry, clean place with at least 30 cm on the top, 20 cm on the right and left, and 10 cm at the back of this unit for ventilation space -- away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid. [. . . ] The entire range of the rear channel signal is directed to the left and right rear speakers. The low-frequency signals (90 Hz and below) of the rear channel are directed to the speakers selected with "BASS OUT". NON Select this if you do not have rear speakers. LRG Select this if you have a large center speaker. The entire range of the center channel signal is directed to the center speaker. The lowfrequency signals (90 Hz and below) of the center channel are directed to the speakers selected with "BASS OUT". All of the center channel signals are directed to the left and right main speakers. y · This unit is set in the Virtual CINEMA DSP mode by selecting NON for "REAR LR SP". 36 SET MENU I BASS OUT (bass out mode) LFE signals carry low-frequency effects when this unit decodes a Dolby Digital or DTS signal. Choices: SWFR (subwoofer), MAIN, BOTH Initial setting: BOTH 2 HP TONE CTRL (headphone tone control) Use this feature to adjust the level of the bass and treble when you use your headphones. Control range (dB): ­6 to +3 Initial setting: 0 dB for both BASS and TRBL (treble) INTRODUCTION SWFR Select this if you use a subwoofer. BOTH Select this if you use a subwoofer and you want to mix the main channel low-frequency signals with the LFE signals. dB dB PREPARATION 3 I/O ASSIGN It is possible to assign jacks according to the component to be used if this unit's DIGITAL INPUT/OUTPUT jack settings (component names for terminals) differ from that component. This makes it possible to change the jack assignment and effectively connect more component. Once you assign, you can select that component with INPUT l / h (or the input selector buttons). Notes · When playing a 2-channel source (CD, MD, tape, video cassette etc. ), select BOTH position to direct low bass signals (below 90 Hz) to the SUBWOOFER jack. · When you select SMALL (SML) for items "CENTER SP", "MAIN SP" and "REAR LR SP", the low-frequency signals (90 Hz and below) from those channels are added to the LFE and output to the subwoofer. BASIC OPERATION I 3A (1) (for the OPTICAL OUTPUT jack) Initial setting: (1) MD/CD-R I MAIN LVL (main level mode) Change this setting if you cannot match the output level of the center and rear speakers with the main speakers because of the unusually high-efficiency performance of the main speakers. Choices: NORM (normal), ­10 dB Initial setting: NORM I 3B (2) to (4) (for the OPTICAL INPUT jacks) Initial settings: (2) MD/CD-R (3) DVD (4) D-TV/CBL ADVANCED OPERATION NORM (normal) Normally select this setting. APPENDIX ­10 dB Select this if you cannot match the output level of your effect speakers with that of your main speakers when using the test tone. This setting decreases the main speaker output level to about one-third of the normal level. English 37 SET MENU I 3C (5) (for the COAXIAL INPUT jack) Initial setting: (5) CD I D-RANGE (dynamic range) Use this feature to adjust the dynamic range (the difference between the maximum level and the minimum level of sounds). Choices: MAX, STD (standard), MIN Initial setting: MAX Note · You cannot select an item more than once for the same type of jack. 4 INPUT MODE (initial input mode) Use this feature to designate the input mode when turning on the power of this unit with the source component connected to more than one type of input jacks. Choices: AUTO, LAST Initial setting: AUTO · Select MAX for feature films. · Select MIN for listening to sources at an extremely low volume level. MAX Output level Dialog level Input level Output level Dialog level 1. 0 Output level AUTO Select this to allow this unit to automatically detect the type of input signal and select the appropriate input mode. LAST Select this to set this unit to automatically select the last input mode used for that source. STD H-LEVEL CUT 0. 0 1. 0 MIN Dialog level 0. 0 L-LEVEL BST Input level Input level 5 DOLBY D. SET (Dolby Digital set) This setting is effective only when this unit decodes Dolby Digital signals. Note · When you select MIN, the sound output may be faint because some Dolby Digital signals are not compatible with the minimum-level dynamic range. In this case, select MAX or STD. I LFE LEVEL Use this feature to adjust the output level of the LFE (lowfrequency effect) channel when playing back a Dolby Digital signal. The LFE signal carries the low-frequency special effect sound which is only added to certain scenes. Control value (dB): ­20 to 0 Initial setting: 0 dB 6 DTS SET (DTS LFE level) This setting is effective only when this unit decodes DTS signals. [. . . ] 37 I IMPEDANCE SELECTOR switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 INPUT MODE (SET MENU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Input modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 I/O ASSIGN (SET MENU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]