User manual YAMAHA RX-V395

[. . . ] UCA RX-V395 NATURAL SOUND AV RECEIVER AMPLI-TUNER AUDIO-VIDEO OWNER'S MANUAL MODE D'EMPLOI SAFETY INSTRUCTIONS 8. Ventilation ­ The unit should be situated so that its location CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9. [. . . ] q If you select the input selector button for a video source without canceling the selection of TAPE/MD MONITOR, the playback result will be the video image from the video source and the sound from the audio tape (or MD, etc. ). q Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. q When you finish using this unit * If you use two main speaker systems, press both the A and B switches. Press the STANDBY/ON switch on the front panel again or the POWER /I key on the remote control transmitter to put this unit in the standby mode. 22 To listen to a source with Dolby Digital, DTS or other future format by reproducing the decoded signals input at the 6CH DISCRETE INPUT terminals of this unit. In step 3 on page 22, press either the DVD/LD or TV/DBS button once or more so that "6ch" appears in the display. Discrete signals from the component connected to the 6CH DISCRETE INPUT terminals of this unit are selected as the input signals. English To stop listening to a decoded source with Dolby Digital, DTS, or other future format Press the DVD/LD or TV/DBS button again to switch the input from six channel input to two channel input or select another input source. When two channel input is selected, the 6CH DISCRETE INPUT terminals are not used. Notes on reproducing discrete signals with Dolby Digital, DTS, or other future format: 1. * Connect a subwoofer which has a built-in amplifier directly to the SUBWOOFER OUTPUT terminal of this unit. For more details on hooking up a subwoofer to this unit, refer to pages 10 and 12. * If you do not have a subwoofer in your system, it may be possible to make a setting on the Dolby Digital, DTS, or other future format decoder to distribute LFE channel signals to the right and left MAIN output terminals. For details, refer to the owner's manual supplied with your decoder. Notes q When you switch to the "6ch" mode, the built-in digital sound field processor (DSP) will not work and adjustments to delay time settings cannot be made. q Switching this unit to the "6ch" mode will input no signal to this unit if there is no connection made to the 6CH DISCRETE INPUT terminals of this unit. TV/DBS 2CH/6CH DVD/LD 2CH/6CH VCR TV/DBS 2CH/6CH DVD 2CH/ or PHONO CD TAPE/MD MONITOR UNER PHONO CD TA MO 23 TO RECORD A SOURCE TO TAPE OR MD 1 42 L R 1 Select the source to be recorded. 3 4 Begin recording on the tape deck (or MD recorder, etc. ) or VCR connected to this unit. TUNER PHONO CD TAPE/MD MONITOR If the tape deck (or MD recorder, etc. ) is used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MONITOR so that the "TAPE MON" indicator lights up on the display. 2 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on tuning operations, refer to the page 26. ) VOLUME l6 20 l2 TV/DBS 2CH/6CH DVD/LD 2CH/6CH PHONO CD TAPE/MD MONITOR 28 8 40 4 4 60 2 0 ­dB Notes The settings of DSP and the VOLUME, BASS, TREBLE and BALANCE controls have no effect on the material being recorded. q In step 1, do not make an input source selection so that "6ch" appears on the display. Signals input to this unit's 6CH DISCRETE INPUT terminals cannot be recorded by a tape deck, MD recorder or VCR. q 24 English Selecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you English to select speaker system A or B, or both at once. SPEAKERS A B Adjusting the BASS and TREBLE controls BASS 0 l 2 3 4 5 5 2 3 4 5 5 TREBLE 0 l l 2 3 4 l 2 3 4 ON OFF BASS : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. BALANCE 0 l l 2 3 4 L5 2 3 4 5R TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Note These controls are effective only for the sound from the main speakers. Note This control is effective only for the sound from the main speakers. Adjusting the subwoofer output level If your audio system includes a subwoofer, and an amplifier driving the subwoofer (or a subwoofer system including an amplifier) is connected to the SUBWOOFER OUTPUT terminal on the rear of this unit, you can adjust the subwoofer output level on this unit. 1 Press once or more so that "SWFR" appears on the display. DELAY/CENTER/ REAR/SWFR 2 By continuously pressing the "+" or "­" side of the TIME/ LEVEL button, the level value changes continuously. If you feel that bass tone is insufficient, increase the level, and if you feel that bass tone is overly emphasized, decrease the level. TIME/LEVEL Adjustable Control range: MIN, ­20 to 0 dB 25 TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). L R 1 AUTOMATIC TUNING 3 24 MANUAL TUNING 1 Select "TUNER" as the input source. TUNER PHONO CD TAPE/MD MONITOR 1 Select "TUNER" as the input source. TUNER PHONO CD TAPE/MD MONITOR 2 Select the reception band (FM or AM) confirming it in the display. FM/AM 2 Select the reception band (FM or AM) confirming it in the display. FM/AM or or 3 TUNING MODE 3 AUTO TUNING MODE AUTO/MAN'L MONO AUTO/MAN'L MONO Turn the "AUTO" indicator off. 4 To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. DOWN 4 Tune to a desired station manually. DOWN TUNING UP TUNING UP * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. * For a continuous tuning search, press and hold the button. Note If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. 26 English PRESET TUNING MANUAL PRESET TUNING English This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by selecting the preset station number where it is stored. Up to 40 stations (5 groups of 8 stations) can be stored. L R 2, 1 4, 2 3 To store stations To recall a preset station 1 2 Tune to a desired station. [. . . ] 0. 1%/0. 2% Stereo Separation (1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 dB Frequency Response (20 Hz to 15 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 ±1 dB Output Level [Australia, U. K. , and Europe models] (40 kHz Dev. , 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550 mV [U. S. A. , Canada, China and General models] (100% mod. , 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]