User manual YAMAHA RX-V393RDS

[. . . ] GB RXV493RDS RXV393RDS Natural Sound AV Receiver Récepteur audiovisuel "Son Naturel" Natural Sound AV-Receiver Natural Sound AV-receiver Sintonizzatore AV a suono naturale Receptor AV de Sonido Natural Natural Sound AV Ontvanger OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTE ZUBEHÖRTEILE MEDFÖLJANDE TILLBEHÖR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES Indoor FM Antenna Antenne FM intérieure UKW-Innenantenne FM inomhusantenn Antenna FM interna Antena FM interior FM Binnenantenne q q q q q q q After unpacking, check that the following parts are included. Après le déballage, vérifier que les pièces suivantes sont incluses. Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. Kontrollera efter det apparaten packats upp att följande delar finns med. [. . . ] * Select "CENTER" to adjust the output level of the center speaker, and select "REAR" to adjust the output level of the rear speakers. DELAY/CENTER /REAR/SWFR Disappears. b) Adjust its level. TIME/ ­ LEVEL Notes Once you have completed these adjustments, you can adjust whole sound level on your audio system by using the VOLUME control (or the VOLUME keys on the remote control transmitter) only. q If you use external power amplifiers, you may also use their volume controls to achieve proper balance. q If there is insufficient sound output from the center and rear speakers, you may decrease the main speaker output level by setting the MAIN LEVEL switch on the rear panel to "­10 dB". q q + RX-V493RDS only In step 9, if the center channel mode is in the "PHANTOM" position, the sound output level of the center speaker cannot be adjusted. This is because in this mode, the center sound is automatically output from the left and right main speakers. RX-V393RDS CENTER LEVEL REAR LEVEL 0 l0 0 l0 24 From page 25 to 41, this manual describes how to operate this unit mainly by using the front panel control parts. To operate this unit on the remote control transmitter, use the corresponding keys on the remote control transmitter. English BASIC OPERATIONS TO PLAY A SOURCE 2 3 20 28 40 1, 6 l6 l2 8 4 60 2 0 ­dB 4 1 20 28 40 7 5 Play the source. (For detailed information on the tuning operation, refer to page 29. ) VOLUME l6 20 l2 VOLUME l6 l2 8 4 6 28 40 60 2 8 0 ­dB 4 Set to the "" position. 60 2 0 ­dB 2 Turn the power on. STANDBY/ON Adjust to the desired output level. 7 3 Select the desired input source by using the input selector buttons. (For video sources, turn the TV/monitor ON. ) TUNER PHONO CD If desired, adjust the BASS, TREBLE and BALANCE controls (refer to page 28), and use the digital sound field processor. (Refer to page 39. ) * The name of the selected input source will appear on the display. 4 Select the main speakers to be used. SPEAKERS A B Notes on using the input selector buttons Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. q The selection of TAPE/MD MONITOR (MON) cannot be canceled by pressing another input selector button. To cancel it, press TAPE/MD MONITOR (MON) again so that the "TAPE MON" indicator disappears from the display. When you select a button other than TAPE/MD MONITOR (MON), make sure that the "TAPE MON" indicator is not illuminated on the display. q If you select the input selector button for a video source without canceling the selection of TAPE/MD MONITOR (MON), the playback result will be the video image from the video source and the sound from the audio tape (or MD etc. ). q Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. q ON OFF * If you use two main speaker systems, press both the A and B switches. When you finish using this unit Press the STANDBY/ON switch on the front panel again or the POWER /I key on the remote control transmitter to turn this unit into the standby mode. 25 To listen to a decoded source using Dolby Digital (AC-3) or DTS by reproducing the signals input to the 6CH DISCRETE INPUT terminals of this unit. In step 3, press the button (shown below) once or more so that "6ch" appears on the display. Discrete signals from the unit connected to the 6CH DISCRETE INPUT terminals of this unit are selected as the input signals. To cancel listening to a decoded source using Dolby Digital (AC-3) or DTS Press the same button again or select another input source. Note for reproducing discrete signals with Dolby Digital (AC-3) or DTS decoded: 1. * Connect a subwoofer which has a built-in amplifier to the SUBWOOFER OUTPUT terminal of this unit. If you do so, you should make a setting for distributing signals at the LFE channel to the right and left MAIN output terminals on the Dolby Digital (AC-3) Decoder etc. For details, refer to the owner's manual for the Dolby Digital (AC-3) Decoder etc. Notes q When you switch to the "6ch" mode, the built-in Digital Sound Field processor will not work and adjustment of delay time cannot be made. q RX-V493RDS TV/DBS DVD/LD TV/DBS DVD/LD or TAPE/MD MON 2CH/6CH TAPE/MD MON 2CH/6CH RX-V393RDS VCR VIDEO Switching this unit to the "6ch" mode will input no signal to this unit if there is no connection to the 6CH DISCRETE INPUT terminals of this unit. 2CH/6CH 26 English TO RECORD A SOURCE TO TAPE (OR MD) RX-V493RDS RX-V393RDS 14 28 40 2 l6 20 l2 8 4 4 12 l6 20 l2 28 8 40 4 60 2 60 2 0 ­dB ­dB 0 1 Select the source to be recorded. 3 CD Begin recording on the tape deck (or MD recorder etc. ) or VCR connected to this unit. If the tape deck (or MD recorder etc. ) is used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MONITOR (MON) so that the "TAPE MON" indicator lights up on the display. RX-V393RDS DVD/LD TUNER PHONO 4 2 RX-V493RDS Play the source and then turn the VOLUME control up to confirm the input source. [. . . ] A desired station cannot be tuned in with the automatic tuning method. AM FM There are continuous crackling and hissing noises. There are buzzing and whining noises (especially in the evening). Noises will result from ligtning, fluorescent lamps, motors, thermostats and other electrical equipment. Direct sunlight or lighting (of an inverter type of fluorescent lamp etc. ) is striking the remote control sensor of the main unit. The batteries of this remote control transmitter are too weak. Remote control transmitter The remote control transmitter does not work. Replace the batteries with new ones. [. . . ]